lkml.org 
[lkml]   [2024]   [Mar]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH] thermal: gov_power_allocator: Allow binding without cooling devices
From
Hi Rafael,

On 3/27/24 15:25, Rafael J. Wysocki wrote:
> On Thu, Mar 21, 2024 at 3:44 PM Nikita Travkin <nikita@trvn.ru> wrote:
>>
>> Commit e83747c2f8e3 ("thermal: gov_power_allocator: Set up trip points earlier")
>> added a check that would fail binding the governer if there is no
>> cooling devices bound to the thermal zone. Unfortunately this causes
>> issues in cases when the TZ is bound to the governer before the cooling
>> devices are attached to it. (I.e. when the tz is registered using
>> thermal_zone_device_register_with_trips().)
>>
>> Additionally, the documentation across gov_power_allocator suggests it's
>> intended to allow it to be bound to thermal zones without cooling
>> devices (and thus without passive/active trip points), however the same
>> change added a check for the trip point to be present, causing those TZ
>> to fail probing.
>>
>> Those changes cause all thermal zones to fail on some devices (such as
>> sc7180-acer-aspire1) and prevent the kernel from controlling the cpu/gpu
>> frequency based on the temperature, as well as losing all the other
>> "informational" thermal zones if power_allocator is set as default.
>>
>> This commit partially reverts the referenced one by dropping the trip
>> point check and by allowing the TZ to probe even if no actor buffer was
>> allocated to allow those TZ to probe again.
>>
>> Fixes: e83747c2f8e3 ("thermal: gov_power_allocator: Set up trip points earlier")
>> Signed-off-by: Nikita Travkin <nikita@trvn.ru>
>> ---
>> I've noticed that all thermal zones fail probing with -EINVAL on my
>> sc7180 based Acer Aspire 1 since 6.8. This commit allows me to bring
>> them back.
>
> Łukasz, any comments?

Let me check this today.

>
>> ---
>> drivers/thermal/gov_power_allocator.c | 14 +++++---------
>> 1 file changed, 5 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/thermal/gov_power_allocator.c b/drivers/thermal/gov_power_allocator.c
>> index 1b17dc4c219c..4f2d7f3b7508 100644
>> --- a/drivers/thermal/gov_power_allocator.c
>> +++ b/drivers/thermal/gov_power_allocator.c
>> @@ -679,11 +679,6 @@ static int power_allocator_bind(struct thermal_zone_device *tz)
>> return -ENOMEM;
>>
>> get_governor_trips(tz, params);
>> - if (!params->trip_max) {
>> - dev_warn(&tz->device, "power_allocator: missing trip_max\n");
>> - kfree(params);
>> - return -EINVAL;
>> - }
>>
>> ret = check_power_actors(tz, params);
>> if (ret < 0) {
>> @@ -693,7 +688,7 @@ static int power_allocator_bind(struct thermal_zone_device *tz)
>> }
>>
>> ret = allocate_actors_buffer(params, ret);
>> - if (ret) {
>> + if (ret && ret != -EINVAL) {
>> dev_warn(&tz->device, "power_allocator: allocation failed\n");
>> kfree(params);
>> return ret;
>> @@ -714,9 +709,10 @@ static int power_allocator_bind(struct thermal_zone_device *tz)
>> else
>> params->sustainable_power = tz->tzp->sustainable_power;
>>
>> - estimate_pid_constants(tz, tz->tzp->sustainable_power,
>> - params->trip_switch_on,
>> - params->trip_max->temperature);
>> + if (params->trip_max)
>> + estimate_pid_constants(tz, tz->tzp->sustainable_power,
>> + params->trip_switch_on,
>> + params->trip_max->temperature);
>>
>> reset_pid_controller(params);
>>
>>
>> ---
>> base-commit: e7528c088874326d3060a46f572252be43755a86
>> change-id: 20240321-gpa-no-cooling-devs-c79ee3288325
>>
>> Best regards,
>> --
>> Nikita Travkin <nikita@trvn.ru>
>>

\
 
 \ /
  Last update: 2024-05-27 16:13    [W:0.080 / U:0.140 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site