lkml.org 
[lkml]   [2024]   [Feb]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/3] arm64: dts: qcom: x1e80100-crd: switch WSA8845 speakers to shared reset-gpio
Date
Each pair of WSA8845 speakers share the powerdown SD_N GPIO, thus this
GPIO is specified twice in each WSA8845 device node. Such DTS was added
hoping non-exclusive GPIO usage would be accepted, but it turned out
otherwise: it is not supported by the Linux kernel.

Linux kernel however supports sharing reset GPIOs, when used bia the
reset controller framework as implemented in commit 26c8a435fce6 ("ASoC:
dt-bindings: qcom,wsa8840: Add reset-gpios for shared line") and
commit c721f189e89c ("reset: Instantiate reset GPIO controller for
shared reset-gpios").

Convert the property with shutdown GPIO to "reset-gpios" to use
mentioned Linux kernel feature. This allows to bring all four speakers
out of reset.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---

Dependencies merged by respective maintainers for next release:
1. ASoC: commit 26c8a435fce6 ("ASoC: dt-bindings: qcom,wsa8840: Add
reset-gpios for shared line")
2. reset: commit c721f189e89c ("reset: Instantiate reset GPIO controller
for shared reset-gpios").
---
arch/arm64/boot/dts/qcom/x1e80100-crd.dts | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
index d7ba45953277..266a461f4882 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-crd.dts
@@ -802,13 +802,14 @@ &smb2360_2_eusb2_repeater {
&swr0 {
status = "okay";

+ pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+ pinctrl-names = "default";
+
/* WSA8845, Left Woofer */
left_woofer: speaker@0,0 {
compatible = "sdw20217020400";
reg = <0 0>;
- pinctrl-0 = <&spkr_01_sd_n_active>;
- pinctrl-names = "default";
- powerdown-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
#sound-dai-cells = <0>;
sound-name-prefix = "WooferLeft";
vdd-1p8-supply = <&vreg_l15b_1p8>;
@@ -819,8 +820,7 @@ left_woofer: speaker@0,0 {
left_tweeter: speaker@0,1 {
compatible = "sdw20217020400";
reg = <0 1>;
- /* pinctrl in left_woofer node because of sharing the GPIO*/
- powerdown-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
#sound-dai-cells = <0>;
sound-name-prefix = "TwitterLeft";
vdd-1p8-supply = <&vreg_l15b_1p8>;
@@ -853,13 +853,14 @@ wcd_tx: codec@0,3 {
&swr3 {
status = "okay";

+ pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
+ pinctrl-names = "default";
+
/* WSA8845, Right Woofer */
right_woofer: speaker@0,0 {
compatible = "sdw20217020400";
reg = <0 0>;
- pinctrl-0 = <&spkr_23_sd_n_active>;
- pinctrl-names = "default";
- powerdown-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
#sound-dai-cells = <0>;
sound-name-prefix = "WooferRight";
vdd-1p8-supply = <&vreg_l15b_1p8>;
@@ -870,8 +871,7 @@ right_woofer: speaker@0,0 {
right_tweeter: speaker@0,1 {
compatible = "sdw20217020400";
reg = <0 1>;
- /* pinctrl in right_woofer node because of sharing the GPIO*/
- powerdown-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
#sound-dai-cells = <0>;
sound-name-prefix = "TwitterRight";
vdd-1p8-supply = <&vreg_l15b_1p8>;
--
2.34.1

\
 
 \ /
  Last update: 2024-05-27 15:24    [W:0.060 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site