lkml.org 
[lkml]   [2024]   [Feb]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v9 1/4] serial: 8250: Add 8250 port clock update method
On Thu, Feb 15, 2024 at 10:32:18PM +0300, Serge Semin wrote:
> On Wed, Feb 14, 2024 at 03:45:16PM +0200, Andy Shevchenko wrote:
> > On Thu, Jul 23, 2020 at 03:33:54AM +0300, Serge Semin wrote:
> > > Some platforms can be designed in a way so the UART port reference clock
> > > might be asynchronously changed at some point. In Baikal-T1 SoC this may
> > > happen due to the reference clock being shared between two UART ports, on
> > > the Allwinner SoC the reference clock is derived from the CPU clock, so
> > > any CPU frequency change should get to be known/reflected by/in the UART
> > > controller as well. But it's not enough to just update the
> > > uart_port->uartclk field of the corresponding UART port, the 8250
> > > controller reference clock divisor should be altered so to preserve
> > > current baud rate setting. All of these things is done in a coherent
> > > way by calling the serial8250_update_uartclk() method provided in this
> > > patch. Though note that it isn't supposed to be called from within the
> > > UART port callbacks because the locks using to the protect the UART port
> > > data are already taken in there.

..

> > > +/*
> > > + * Note in order to avoid the tty port mutex deadlock don't use the next method
> > > + * within the uart port callbacks. Primarily it's supposed to be utilized to
> > > + * handle a sudden reference clock rate change.
> > > + */
> > > +void serial8250_update_uartclk(struct uart_port *port, unsigned int uartclk)
> > > +{
> > > + struct uart_8250_port *up = up_to_u8250p(port);
> > > + unsigned int baud, quot, frac = 0;
> > > + struct ktermios *termios;
> > > + unsigned long flags;
> > > +
> > > + mutex_lock(&port->state->port.mutex);
> > > +
> > > + if (port->uartclk == uartclk)
> > > + goto out_lock;
> > > +
> > > + port->uartclk = uartclk;
> > > + termios = &port->state->port.tty->termios;
> > > +
> > > + baud = serial8250_get_baud_rate(port, termios, NULL);
> > > + quot = serial8250_get_divisor(port, baud, &frac);
> > > +
> > > + serial8250_rpm_get(up);
> > > + spin_lock_irqsave(&port->lock, flags);
> > > +
> > > + uart_update_timeout(port, termios->c_cflag, baud);
> > > +
> > > + serial8250_set_divisor(port, baud, quot, frac);
> > > + serial_port_out(port, UART_LCR, up->lcr);
> > > + serial8250_out_MCR(up, UART_MCR_DTR | UART_MCR_RTS);
> > > +
> > > + spin_unlock_irqrestore(&port->lock, flags);
> > > + serial8250_rpm_put(up);
> > > +
> > > +out_lock:
> > > + mutex_unlock(&port->state->port.mutex);
> >
>
> > While looking for something else I have stumbled over this function.
> > My Q is, since it has some duplications with
> > serial8250_do_set_termios(), can we actually call the latter (or
> > derevative that can be called in both) in the above code instead of
> > duplicating some lines?
> >
> > if (port UART clock has to be updated)
> > call (unlocked version of) serial8250_do_set_termios()
> >
> > Serge, what do you think?
>
> What an old thread you've digged out.)

Indeed :-)

> Well, AFAIR I didn't create a common baud-rate/clock-update method
> because the baud-rate change was just a two stages action:
> 1. calculate divisor+quot couple based on the new clock,
> 2. update the divisor+quot (+ update the timeout).
> The first stage didn't need to have the IRQsafe lock being held and
> the runtime-PM being enabled, meanwhile the later one needed those.
> So unless the nested locking or try-lock-based pattern is implemented
> each stage required dedicated function introduced, which would have
> been an overkill for that. But even if I got to implement the
> try-lock-based solution with a single function containing both stages
> I still couldn't avoid having the serial8250_get_baud_rate() and
> serial8250_get_divisor() methods executed in the atomic context, which
> isn't required for them and which would needlessly pro-long the CPU
> executing with the IRQs disabled. As you well know it's better to
> speed up the atomic context execution as much as possible.
>
> Secondly I didn't know much about the tty/serial subsystem internals
> back then. So I was afraid to break some parts I didn't aware of if
> the baud-rate/ref-clock change code had some implicit dependencies
> from the surrounding code and vice-versa (like the LCR DLAB flag
> state).
>
> Finally frankly it didn't seem like that much worth bothering about.
> Basically AFAICS there were only four methods which invocation I
> would have needed to move to a separate function:
>
> serial8250_get_baud_rate();
> serial8250_get_divisor();
> // spin-lock
> uart_update_timeout(port, termios->c_cflag, baud);
> serial8250_set_divisor(port, baud, quot, frac);
> // spin-unlock
>
> So I decided to take a simplest and safest path, and created a
> dedicated method for the just the ref-clock updates case leaving the
> baud-rate change task implemented in the framework of the standard
> serial8250_do_set_termios() method.
>
>
> Regarding doing vise-versa and calling the serial8250_do_set_termios()
> method from serial8250_update_uartclk() instead. To be honest I didn't
> consider that option. That might work though, but AFAICS the
> serial8250_do_set_termios() function will do much more than it's
> required in case if the ref-clock has changed.

My point here is that the idea behind clock change is most likely to be
followed up by ->set_termios(). Why to do it differently if it's the case?
And note, ->set_termios() can be called as many times as needed, so if nothing
changes in between it's also fine. But this makes intention much clearer.
Do you agree?

--
With Best Regards,
Andy Shevchenko



\
 
 \ /
  Last update: 2024-02-15 20:39    [W:2.226 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site