Messages in this thread Patch in this message | | | From | Christophe Roullier <> | Subject | [PATCH v2 11/12] ARM: dts: stm32: add ethernet1 and ethernet2 for STM32MP135F-DK board | Date | Thu, 28 Sep 2023 14:24:26 +0200 |
| |
Add dual Ethernet: -Ethernet1: RMII with crystal -Ethernet2: RMII without crystal PHYs used are SMSC (LAN8742A)
With Ethernet1, we can performed WoL from PHY instead of GMAC point of view. (in this case IRQ for WoL is managed as wakeup pin and configured in OS secure).
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com> --- arch/arm/boot/dts/st/stm32mp135f-dk.dts | 48 +++++++++++++++++++++++++ 1 file changed, 48 insertions(+)
diff --git a/arch/arm/boot/dts/st/stm32mp135f-dk.dts b/arch/arm/boot/dts/st/stm32mp135f-dk.dts index eea740d097c72..1316cc16f8dd9 100644 --- a/arch/arm/boot/dts/st/stm32mp135f-dk.dts +++ b/arch/arm/boot/dts/st/stm32mp135f-dk.dts @@ -19,6 +19,8 @@ / { compatible = "st,stm32mp135f-dk", "st,stm32mp135"; aliases { + ethernet0 = ðernet1; + ethernet1 = ðernet2; serial0 = &uart4; serial1 = &usart1; serial2 = &uart8; @@ -93,6 +95,52 @@ channel@12 { }; }; +ðernet1 { + status = "okay"; + pinctrl-0 = <ð1_rmii_pins_a>; + pinctrl-1 = <ð1_rmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + max-speed = <100>; + phy-handle = <&phy0_eth1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0_eth1: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.c131"; + reset-gpios = <&mcp23017 9 GPIO_ACTIVE_LOW>; + reg = <0>; + wakeup-source; + }; + }; +}; + +ðernet2 { + status = "okay"; + pinctrl-0 = <ð2_rmii_pins_a>; + pinctrl-1 = <ð2_rmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + max-speed = <100>; + phy-handle = <&phy0_eth2>; + st,ext-phyclk; + phy-supply = <&scmi_v3v3_sw>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy0_eth2: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.c131"; + reset-gpios = <&mcp23017 10 GPIO_ACTIVE_LOW>; + reg = <0>; + }; + }; +}; + &i2c1 { pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c1_pins_a>; -- 2.25.1
| |