Messages in this thread Patch in this message | | | Date | Sat, 5 Aug 2023 17:23:11 +0100 | From | Daniel Golle <> | Subject | [PATCH v2 1/7] mtd: ubi: improve Kconfig formatting |
| |
Kconfig help text should be indented with one tab + 2 spaces according to coding-style.rst. Apply this rule in drivers/mtd/ubi/Kconfig
Signed-off-by: Daniel Golle <daniel@makrotopia.org> --- drivers/mtd/ubi/Kconfig | 60 ++++++++++++++++++++--------------------- 1 file changed, 30 insertions(+), 30 deletions(-)
diff --git a/drivers/mtd/ubi/Kconfig b/drivers/mtd/ubi/Kconfig index 2ed77b7b3fcb5..184118f9a2969 100644 --- a/drivers/mtd/ubi/Kconfig +++ b/drivers/mtd/ubi/Kconfig @@ -61,47 +61,47 @@ config MTD_UBI_FASTMAP bool "UBI Fastmap (Experimental feature)" default n help - Important: this feature is experimental so far and the on-flash - format for fastmap may change in the next kernel versions - - Fastmap is a mechanism which allows attaching an UBI device - in nearly constant time. Instead of scanning the whole MTD device it - only has to locate a checkpoint (called fastmap) on the device. - The on-flash fastmap contains all information needed to attach - the device. Using fastmap makes only sense on large devices where - attaching by scanning takes long. UBI will not automatically install - a fastmap on old images, but you can set the UBI module parameter - fm_autoconvert to 1 if you want so. Please note that fastmap-enabled - images are still usable with UBI implementations without - fastmap support. On typical flash devices the whole fastmap fits - into one PEB. UBI will reserve PEBs to hold two fastmaps. - - If in doubt, say "N". + Important: this feature is experimental so far and the on-flash + format for fastmap may change in the next kernel versions + + Fastmap is a mechanism which allows attaching an UBI device + in nearly constant time. Instead of scanning the whole MTD device it + only has to locate a checkpoint (called fastmap) on the device. + The on-flash fastmap contains all information needed to attach + the device. Using fastmap makes only sense on large devices where + attaching by scanning takes long. UBI will not automatically install + a fastmap on old images, but you can set the UBI module parameter + fm_autoconvert to 1 if you want so. Please note that fastmap-enabled + images are still usable with UBI implementations without + fastmap support. On typical flash devices the whole fastmap fits + into one PEB. UBI will reserve PEBs to hold two fastmaps. + + If in doubt, say "N". config MTD_UBI_GLUEBI tristate "MTD devices emulation driver (gluebi)" help - This option enables gluebi - an additional driver which emulates MTD - devices on top of UBI volumes: for each UBI volumes an MTD device is - created, and all I/O to this MTD device is redirected to the UBI - volume. This is handy to make MTD-oriented software (like JFFS2) - work on top of UBI. Do not enable this unless you use legacy - software. + This option enables gluebi - an additional driver which emulates MTD + devices on top of UBI volumes: for each UBI volumes an MTD device is + created, and all I/O to this MTD device is redirected to the UBI + volume. This is handy to make MTD-oriented software (like JFFS2) + work on top of UBI. Do not enable this unless you use legacy + software. config MTD_UBI_BLOCK bool "Read-only block devices on top of UBI volumes" default n depends on BLOCK help - This option enables read-only UBI block devices support. UBI block - devices will be layered on top of UBI volumes, which means that the - UBI driver will transparently handle things like bad eraseblocks and - bit-flips. You can put any block-oriented file system on top of UBI - volumes in read-only mode (e.g., ext4), but it is probably most - practical for read-only file systems, like squashfs. + This option enables read-only UBI block devices support. UBI block + devices will be layered on top of UBI volumes, which means that the + UBI driver will transparently handle things like bad eraseblocks and + bit-flips. You can put any block-oriented file system on top of UBI + volumes in read-only mode (e.g., ext4), but it is probably most + practical for read-only file systems, like squashfs. - When selected, this feature will be built in the UBI driver. + When selected, this feature will be built in the UBI driver. - If in doubt, say "N". + If in doubt, say "N". endif # MTD_UBI -- 2.41.0
| |