lkml.org 
[lkml]   [2023]   [Aug]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 3/3] arm64: dts: qcom: ipq5018: enable the CPUFreq support
On Tue, 29 Aug 2023 at 13:10, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
>
> On 29/08/2023 12:56, Robert Marko wrote:
> >
> > On 29. 08. 2023. 12:12, Krzysztof Kozlowski wrote:
> >> On 29/08/2023 11:54, Gokul Sriram Palanisamy wrote:
> >>> Add the APCS, A53 PLL, cpu-opp-table nodes to set
> >>> the CPU frequency at optimal range.
> >>>
> >>> Co-developed-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
> >>> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com>
> >>> Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri@quicinc.com>
> >>> ---
> >>> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 34 +++++++++++++++++++++++++++
> >>> 1 file changed, 34 insertions(+)
> >>>
> >>> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> >>> index 9f13d2dcdfd5..05843517312c 100644
> >>> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> >>> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> >>> @@ -8,6 +8,7 @@
> >>> #include <dt-bindings/interrupt-controller/arm-gic.h>
> >>> #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
> >>> #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
> >>> +#include <dt-bindings/clock/qcom,apss-ipq.h>
> >> c is before r.
> >>
> >>>
> >>> / {
> >>> interrupt-parent = <&intc>;
> >>> @@ -36,6 +37,8 @@ CPU0: cpu@0 {
> >>> reg = <0x0>;
> >>> enable-method = "psci";
> >>> next-level-cache = <&L2_0>;
> >>> + clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
> >>> + operating-points-v2 = <&cpu_opp_table>;
> >>> };
> >>>
> >>> CPU1: cpu@1 {
> >>> @@ -44,6 +47,8 @@ CPU1: cpu@1 {
> >>> reg = <0x1>;
> >>> enable-method = "psci";
> >>> next-level-cache = <&L2_0>;
> >>> + clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
> >>> + operating-points-v2 = <&cpu_opp_table>;
> >>> };
> >>>
> >>> L2_0: l2-cache {
> >>> @@ -54,6 +59,17 @@ L2_0: l2-cache {
> >>> };
> >>> };
> >>>
> >>> + cpu_opp_table: opp-table-cpu {
> >>> + compatible = "operating-points-v2";
> >>> + opp-shared;
> >>> +
> >>> + opp-1008000000 {
> >>> + opp-hz = /bits/ 64 <1008000000>;
> >>> + opp-microvolt = <1100000>;
> >>> + clock-latency-ns = <200000>;
> >> And the rest of OPPs?
> > Hi Krzysztof,
> > IPQ5018 only supports running at 1.1GHz, but its running at 800MHz
> > by default from the bootloader so there is only one OPP.
>
> Isn't this contradictory? If it is running at 800 initially, then it
> supports running at 800...

I can only guess that it's not validated at 800MHz.

Regards,
Robert
>
>
> Best regards,
> Krzysztof
>

\
 
 \ /
  Last update: 2023-08-29 13:19    [W:0.093 / U:0.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site