lkml.org 
[lkml]   [2023]   [Aug]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [net-next RFC 0/1] mlx5: support per queue coalesce settings
From
Hi Saeed,

Thank you for your review and feedback. Please see below for a couple of
additional questions.

On 8/24/23 14:51, Saeed Mahameed wrote:
> On 23 Aug 18:31, Nabil S. Alramli wrote:
>> Hello,
>>
>> I am Submitting this as an RFC to get feedback and to find out if the
>> folks
>> at Mellanox would accept this change.
>>
>> Currently, only gobal coalescing configuration queries or changes are
>> supported in the `mlx5` driver. However, per-queue operations are not,
>> and
>> result in `EOPNOTSUPP` errors when attempted with `ethtool`. This patch
>> adds support for per-queue coalesce operations, with a caveat described
>> below.
>>
>> Here's an example use case:
>>
>> - An mlx5 NIC is configured with 8 queues, each queue has its IRQ pinned
>>  to a unique CPU.
>> - Two custom RSS contexts are created: context 1 and context 2. Each
>>  context has a different set of queues where flows are distributed. For
>>  example, context 1 may distribute flows to queues 0-3, and context 2 may
>>  distribute flows to queues 4-7.
>> - A series of ntuple filters are installed which direct matching flows to
>>  RSS contexts. For example, perhaps port 80 is directed to context 1 and
>>  port 443 to context 2.
>> - Applications which receive network data associated with either context
>>  are pinned to the CPUs where the queues in the matching context have
>>  their IRQs pinned to maximize locality.
>>
>> The apps themselves, however, may have different requirements on
>> latency vs
>> CPU usage and so setting the per queue IRQ coalesce values would be very
>> helpful.
>>
>> This patch would support this, with the caveat that DIM mode changes per
>> queue are not supported. DIM mode can only be changed NIC-wide. This is
>> because in the mlx5 driver, global operations that change the state of
>> adaptive-ex or adaptive-tx require a reset. So in the case of
>> per-queue, we
>> reject such requests. This was done in the interest of simplicity for
>> this
>> RFC as setting the DIM mode per queue appears to require significant
>> changes to mlx5 to be able to preserve the state of the indvidual
>> channels
>> through a reset.
>>
>> IMO, if a user is going to set per-queue coalesce settings it might be
>> reasonable to assume that they will disable adaptive rx/tx NIC wide first
>> and then go through and apply their desired per-queue settings.
>>
>
> DIM is already per channel, so I don't think it's that difficult to have
> mix support of DIM and static config per channel. Yes the code will need
> some refactoring, but with a quick glance at the code provided here, such
> refactoring is already required IMO.
>
That sounds good. I'll go ahead and add support for DIM per-channel
coalescing updates. I'll send another RFC when that is ready for initial
feedback.

Can you please provide some clarification as to what you mean that some
refactoring is needed? Are you referring to the existing code, or is
there something specifically in this patch?

For example, I think we'll need to make some additional changes to
mlx5e_safe_switch_params(), mlx5e_open_channels() and probably more. Is
this what you have in mind?

>> Here's an example:
>>
>> $ ethtool --per-queue eth0 queue_mask 0x4 --show-coalesce
>> Queue: 2
>> Adaptive RX: on  TX: on
>> stats-block-usecs: 0
>> sample-interval: 0
>> pkt-rate-low: 0
>> pkt-rate-high: 0
>>
>> rx-usecs: 8
>> rx-frames: 128
>> ...
>>
>> Now, let's try to set adaptive-rx off rx-usecs 16 for queue 2:
>>
>> $ sudo ethtool --per-queue eth0 queue_mask 0x4 --coalesce adaptive-rx
>> off \
>>  rx-usecs 16
>> Cannot set device per queue parameters: Operation not supported
>>
>> This is not supported; adaptive-rx must be disabled NIC wide first:
>>
>> $ sudo ethtool -C eth0 adaptive-rx off
>>
>> And now, queue_mask 0x4 can be applied to set rx-usecs:
>>
>> $ sudo ethtool --per-queue eth0 queue_mask 0x4 --coalesce rx-usecs 16
>> $ ethtool --per-queue eth0 queue_mask 0x4 --show-coalesce
>> Queue: 2
>> Adaptive RX: off  TX: on
>> stats-block-usecs: 0
>> sample-interval: 0
>> pkt-rate-low: 0
>> pkt-rate-high: 0
>>
>> rx-usecs: 16
>> rx-frames: 32
>> ...
>>
>> Previously a global `struct mlx5e_params` stored the options in
>> `struct mlx5e_priv.channels.params`. That was preserved, but a channel-
>> specific instance was added as well, in `struct mlx5e_channel.params`.
>>
>> Note that setting global coalescing options will set the individual
>> channel settings to the same values as well.
>>
>> Is Mellanox open to this change? What would be needed to get something
>> like
>> this accepted?
>>
>
> Sure, we just need to pass review and few testing cycles.
>
> Thanks,
> Saeed.
>

Best Regards,

-- Nabil S. Alramli

\
 
 \ /
  Last update: 2023-08-25 02:43    [W:0.115 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site