lkml.org 
[lkml]   [2023]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH 02/11] drm/bridge: tc358768: Fix bit updates
From
On 15/08/2023 20:21, Maxim Schwalm wrote:
> On 14.08.23 08:34, Tomi Valkeinen wrote:
>> On 13/08/2023 03:23, Maxim Schwalm wrote:
>>> Hi,
>>>
>>> On 11.08.23 19:02, Tomi Valkeinen wrote:
>>>> On 11/08/2023 19:23, Péter Ujfalusi wrote:
>>>>>
>>>>>
>>>>> On 04/08/2023 13:44, Tomi Valkeinen wrote:
>>>>>> The driver has a few places where it does:
>>>>>>
>>>>>> if (thing_is_enabled_in_config)
>>>>>> update_thing_bit_in_hw()
>>>>>>
>>>>>> This means that if the thing is _not_ enabled, the bit never gets
>>>>>> cleared. This affects the h/vsyncs and continuous DSI clock bits.
>>>>>
>>>>> I guess the idea was to keep the reset value unless it needs to be flipped.
>>>>>
>>>>>>
>>>>>> Fix the driver to always update the bit.
>>>>>>
>>>>>> Fixes: ff1ca6397b1d ("drm/bridge: Add tc358768 driver")
>>>>>> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
>>>>>> ---
>>>>>> drivers/gpu/drm/bridge/tc358768.c | 13 +++++++------
>>>>>> 1 file changed, 7 insertions(+), 6 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/gpu/drm/bridge/tc358768.c b/drivers/gpu/drm/bridge/tc358768.c
>>>>>> index bc97a837955b..b668f77673c3 100644
>>>>>> --- a/drivers/gpu/drm/bridge/tc358768.c
>>>>>> +++ b/drivers/gpu/drm/bridge/tc358768.c
>>>>>> @@ -794,8 +794,8 @@ static void tc358768_bridge_pre_enable(struct drm_bridge *bridge)
>>>>>> val |= BIT(i + 1);
>>>>>> tc358768_write(priv, TC358768_HSTXVREGEN, val);
>>>>>>
>>>>>> - if (!(mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS))
>>>>>> - tc358768_write(priv, TC358768_TXOPTIONCNTRL, 0x1);
>>>>>> + tc358768_write(priv, TC358768_TXOPTIONCNTRL,
>>>>>> + (mode_flags & MIPI_DSI_CLOCK_NON_CONTINUOUS) ? 0 : BIT(0));
>>>>>>
>>>>>> /* TXTAGOCNT[26:16] RXTASURECNT[10:0] */
>>>>>> val = tc358768_to_ns((lptxcnt + 1) * dsibclk_nsk * 4);
>>>>>> @@ -861,11 +861,12 @@ static void tc358768_bridge_pre_enable(struct drm_bridge *bridge)
>>>>>> tc358768_write(priv, TC358768_DSI_HACT, hact);
>>>>>>
>>>>>> /* VSYNC polarity */
>>>>>> - if (!(mode->flags & DRM_MODE_FLAG_NVSYNC))
>>>>>> - tc358768_update_bits(priv, TC358768_CONFCTL, BIT(5), BIT(5));
>>>>>> + tc358768_update_bits(priv, TC358768_CONFCTL, BIT(5),
>>>>>> + (mode->flags & DRM_MODE_FLAG_PVSYNC) ? BIT(5) : 0);
>>>>>
>>>>> Was this the reverse before and should be:
>>>>> (mode->flags & DRM_MODE_FLAG_PVSYNC) ? 0 : BIT(5)
>>>>
>>>> Bit 5 is 1 for active high vsync polarity. The test was previously
>>>> !nvsync, i.e. the same as pvsync.
>>>
>>> this statement doesn't seem to be true, since this change causes a
>>> regression on the Asus TF700T. Apparently, !nvsync is true and pvsync is
>>> false in the present case.
>>
>> panasonic_vvx10f004b00_mode in panel_simple.c doesn't seem to have mode
>> flags set. I would say that means the panel doesn't care about the sync
>> polarities (which obviously is not the case), but maybe there's an
>> assumption that if sync polarities are not set, the default is...
>> positive? But I can't find any mention about this.
>>
>> Does it work for you if you set the polarities in
>> panasonic_vvx10f004b00_mode?
>
> The panel seems to work with either negative or positive H-/Vsync in
> conjunction with the attached patch from Thierry. Currently, the display
> controller is unconditionally programmed for positive H-/Vsync though.
> What should be done in this case?
>
> BTW, the vendor kernel configures the display controller as well as the
> bridge for negative H-/Vsync.

Also regarding the tegra driver, with a quick look it indeed looks like
it is configuring hardcoded sync polarities, which is not good. Maybe
it's time to apply the patch from Thierry, dated 2015 =).

Tomi

\
 
 \ /
  Last update: 2023-08-16 10:22    [W:0.076 / U:2.568 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site