lkml.org 
[lkml]   [2023]   [Aug]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v8 09/16] media: cadence: csi2rx: Soft reset the streams before starting capture
From
On 31/07/2023 11:29, Jai Luthra wrote:
> From: Pratyush Yadav <p.yadav@ti.com>
>
> This resets the stream state machines and FIFOs, giving them a clean
> slate. On J721E if the streams are not reset before starting the
> capture, the captured frame gets wrapped around vertically on every run
> after the first.
>
> Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> Signed-off-by: Jai Luthra <j-luthra@ti.com>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> ---
> v7->v8: No change
>
> drivers/media/platform/cadence/cdns-csi2rx.c | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
> diff --git a/drivers/media/platform/cadence/cdns-csi2rx.c b/drivers/media/platform/cadence/cdns-csi2rx.c
> index 2a80c66fb547..30cdc260b46a 100644
> --- a/drivers/media/platform/cadence/cdns-csi2rx.c
> +++ b/drivers/media/platform/cadence/cdns-csi2rx.c
> @@ -40,6 +40,7 @@
> #define CSI2RX_STREAM_BASE(n) (((n) + 1) * 0x100)
>
> #define CSI2RX_STREAM_CTRL_REG(n) (CSI2RX_STREAM_BASE(n) + 0x000)
> +#define CSI2RX_STREAM_CTRL_SOFT_RST BIT(4)
> #define CSI2RX_STREAM_CTRL_START BIT(0)
>
> #define CSI2RX_STREAM_DATA_CFG_REG(n) (CSI2RX_STREAM_BASE(n) + 0x008)
> @@ -138,12 +139,22 @@ struct csi2rx_priv *v4l2_subdev_to_csi2rx(struct v4l2_subdev *subdev)
>
> static void csi2rx_reset(struct csi2rx_priv *csi2rx)
> {
> + unsigned int i;
> +
> writel(CSI2RX_SOFT_RESET_PROTOCOL | CSI2RX_SOFT_RESET_FRONT,
> csi2rx->base + CSI2RX_SOFT_RESET_REG);
>
> udelay(10);
>
> writel(0, csi2rx->base + CSI2RX_SOFT_RESET_REG);
> +
> + /* Reset individual streams. */
> + for (i = 0; i < csi2rx->max_streams; i++) {
> + writel(CSI2RX_STREAM_CTRL_SOFT_RST,
> + csi2rx->base + CSI2RX_STREAM_CTRL_REG(i));
> + usleep_range(10, 20);
> + writel(0, csi2rx->base + CSI2RX_STREAM_CTRL_REG(i));
> + }

Do you have to do it like this? Or would it be fine to set the reset bit
for all stream regs, then sleep, then clear the reset bit from all
stream regs? Or going even further, can you set the
CSI2RX_SOFT_RESET_REG and all CSI2RX_STREAM_CTRL_REG regs, then sleep,
and then clear them all?

Tomi

\
 
 \ /
  Last update: 2023-08-01 16:18    [W:0.239 / U:0.832 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site