lkml.org 
[lkml]   [2023]   [Jul]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2 6/8] PCI: qcom: ep: Add wake up host op to dw_pcie_ep_ops
From

On 7/7/2023 11:40 AM, Manivannan Sadhasivam wrote:
> On Fri, Jun 30, 2023 at 04:22:09PM +0530, Krishna chaitanya chundru wrote:
>
> Subject prefix should be "PCI: qcom-ep:"
>
>> Add wakeup host op to dw_pcie_ep_ops to wake up host.
>> If the EPF asks to send PME trigger the inband PME by writing
>> into the parf registers otherwise toggle wake signal.
>>
> If the wakeup type is PME, then trigger inband PME by writing to the PARF
> PARF_PM_CTRL register, otherwise toggle #WAKE.
>
>> Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
>> ---
>> drivers/pci/controller/dwc/pcie-qcom-ep.c | 31 +++++++++++++++++++++++++++++++
>> 1 file changed, 31 insertions(+)
>>
>> diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
>> index e75aec4..e382b4b 100644
>> --- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
>> +++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
>> @@ -89,6 +89,7 @@
>> /* PARF_PM_CTRL register fields */
>> #define PARF_PM_CTRL_REQ_EXIT_L1 BIT(1)
>> #define PARF_PM_CTRL_READY_ENTR_L23 BIT(2)
>> +#define PARF_PM_CTRL_XMT_PME BIT(4)
>> #define PARF_PM_CTRL_REQ_NOT_ENTR_L1 BIT(5)
>>
>> /* PARF_MHI_CLOCK_RESET_CTRL fields */
>> @@ -729,10 +730,40 @@ static void qcom_pcie_ep_init(struct dw_pcie_ep *ep)
>> dw_pcie_ep_reset_bar(pci, bar);
>> }
>>
>> +static int qcom_pcie_ep_wakeup_host(struct dw_pcie_ep *ep, u8 func_no,
>> + enum pci_epc_wakeup_host_type type)
>> +{
>> + struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
>> + struct qcom_pcie_ep *pcie_ep = to_pcie_ep(pci);
>> + struct device *dev = pci->dev;
>> + u32 val;
>> +
>> + if (type == PCI_WAKEUP_TOGGLE_WAKE) {
>> + dev_dbg(dev, "Waking up the host by toggling WAKE#\n");
>> + gpiod_set_value_cansleep(pcie_ep->wake, 1);
>> + usleep_range(WAKE_DELAY_US, WAKE_DELAY_US + 500);
>> + gpiod_set_value_cansleep(pcie_ep->wake, 0);
>> + return 0;
>> +
>> + } else if (type == PCI_WAKEUP_SEND_PME) {
>> + dev_dbg(dev, "Waking up the host using PME\n");
>> + val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
>> + val |= PARF_PM_CTRL_XMT_PME;
>> + writel_relaxed(val, pcie_ep->parf + PARF_PM_CTRL);
>> +
>> + } else {
>> + dev_err(dev, "Device is not in D3 state wakeup is not supported\n");
>> + return -EOPNOTSUPP;
> This is not needed if you use bool. And this debug message is wrong btw since
> you are not checking whether the device is in D3 state or not.
>
> - Mani

I will change it bool and will remove these.

- KC

>
>> + }
>> +
>> + return 0;
>> +}
>> +
>> static const struct dw_pcie_ep_ops pci_ep_ops = {
>> .ep_init = qcom_pcie_ep_init,
>> .raise_irq = qcom_pcie_ep_raise_irq,
>> .get_features = qcom_pcie_epc_get_features,
>> + .wakeup_host = qcom_pcie_ep_wakeup_host,
>> };
>>
>> static int qcom_pcie_ep_probe(struct platform_device *pdev)
>> --
>> 2.7.4
>>

\
 
 \ /
  Last update: 2023-07-07 12:59    [W:0.087 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site