lkml.org 
[lkml]   [2023]   [Jul]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v2 1/2] hwmon: (isl28022) new driver for ISL28022 power monitor
From
On 7/27/23 12:55, Carsten Spieß wrote:
> Driver for Renesas ISL28022 power monitor with I2C interface.
> The device monitors voltage, current via shunt resistor
> and calculated power.
>
> Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>

Change log missing. I am not going to review patches without change log.

Guenter

> ---
> Documentation/hwmon/index.rst | 1 +
> Documentation/hwmon/isl28022.rst | 63 ++++
> MAINTAINERS | 7 +
> drivers/hwmon/Kconfig | 11 +
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/isl28022.c | 496 +++++++++++++++++++++++++++++++
> 6 files changed, 579 insertions(+)
> create mode 100644 Documentation/hwmon/isl28022.rst
> create mode 100644 drivers/hwmon/isl28022.c
>
> diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
> index d11924667f76..c9548fc5c40e 100644
> --- a/Documentation/hwmon/index.rst
> +++ b/Documentation/hwmon/index.rst
> @@ -90,6 +90,7 @@ Hardware Monitoring Kernel Drivers
> ir35221
> ir38064
> ir36021
> + isl28022
> isl68137
> it87
> jc42
> diff --git a/Documentation/hwmon/isl28022.rst b/Documentation/hwmon/isl28022.rst
> new file mode 100644
> index 000000000000..8d4422a2dacd
> --- /dev/null
> +++ b/Documentation/hwmon/isl28022.rst
> @@ -0,0 +1,63 @@
> +.. SPDX-License-Identifier: GPL-2.0-or-later
> +
> +Kernel driver isl28022
> +======================
> +
> +Supported chips:
> +
> + * Renesas ISL28022
> +
> + Prefix: 'isl28022'
> +
> + Addresses scanned: none
> +
> + Datasheet: Publicly available at the Renesas website
> +
> + https://www.renesas.com/us/en/www/doc/datasheet/isl28022.pdf
> +
> +Author:
> + Carsten Spieß <mail@carsten-spiess.de>
> +
> +Description
> +-----------
> +
> +The ISL28022 is a power monitor with I2C interface. The device monitors
> +voltage, current via shunt resistor and calculated power.
> +
> +Usage Notes
> +-----------
> +
> +This driver does not auto-detect devices. You will have to instantiate the
> +device explicitly. Please see Documentation/i2c/instantiating-devices.rst for
> +details.
> +
> +The shunt value in micro-ohms, shunt voltage range and averaging can be set
> +with device properties.
> +Please refer to the Documentation/devicetree/bindings/hwmon/isl,isl28022.yaml
> +for bindings if the device tree is used.
> +
> +The driver supports only shunt and bus continuous ADC mode at 15bit resolution.
> +Averaging can be set from 1 to 128 samples (power of 2) on both channels.
> +Shunt voltage range of 40, 80, 160 or 320mV is allowed
> +The bus voltage range is 60V fixed.
> +
> +Sysfs entries
> +-------------
> +
> +The following attributes are supported. All attributes are read-only.
> +
> +======================= =======================================================
> +in0_input bus voltage (milli Volt)
> +
> +curr1_input current (milli Ampere)
> +power1_input power (micro Watt)
> +======================= =======================================================
> +
> +Debugfs entries
> +---------------
> +
> +The following attributes are supported. All attributes are read-only.
> +
> +======================= =======================================================
> +shunt_voltage shunt voltage (micro Volt)
> +======================= =======================================================
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 7abb5710e1bb..b02e3b991676 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -11065,6 +11065,13 @@ F: drivers/isdn/Makefile
> F: drivers/isdn/hardware/
> F: drivers/isdn/mISDN/
>
> +ISL28022 HARDWARE MONITORING DRIVER
> +M: Carsten Spieß <mail@carsten-spiess.de>
> +L: linux-hwmon@vger.kernel.org
> +S: Maintained
> +F: Documentation/hwmon/isl28022.rst
> +F: drivers/hwmon/isl28022.c
> +
> ISOFS FILESYSTEM
> M: Jan Kara <jack@suse.cz>
> L: linux-fsdevel@vger.kernel.org
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 2913299c2c9e..3049c519e6ac 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -800,6 +800,17 @@ config SENSORS_CORETEMP
> sensor inside your CPU. Most of the family 6 CPUs
> are supported. Check Documentation/hwmon/coretemp.rst for details.
>
> +config SENSORS_ISL28022
> + tristate "Renesas ISL28022"
> + depends on I2C
> + select REGMAP_I2C
> + help
> + If you say yes here you get support for ISL28022 power monitor.
> + Check Documentation/hwmon/isl28022.rst for details.
> +
> + This driver can also be built as a module. If so, the module
> + will be called isl28022.
> +
> config SENSORS_IT87
> tristate "ITE IT87xx and compatibles"
> depends on !PPC
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index ff6bfd109c72..4046fed7f48d 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -98,6 +98,7 @@ obj-$(CONFIG_SENSORS_INA2XX) += ina2xx.o
> obj-$(CONFIG_SENSORS_INA238) += ina238.o
> obj-$(CONFIG_SENSORS_INA3221) += ina3221.o
> obj-$(CONFIG_SENSORS_INTEL_M10_BMC_HWMON) += intel-m10-bmc-hwmon.o
> +obj-$(CONFIG_SENSORS_ISL28022) += isl28022.o
> obj-$(CONFIG_SENSORS_IT87) += it87.o
> obj-$(CONFIG_SENSORS_JC42) += jc42.o
> obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o
> diff --git a/drivers/hwmon/isl28022.c b/drivers/hwmon/isl28022.c
> new file mode 100644
> index 000000000000..18b4481d5ff6
> --- /dev/null
> +++ b/drivers/hwmon/isl28022.c
> @@ -0,0 +1,496 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * isl28022.c - driver for Renesas ISL28022 power monitor chip monitoring
> + *
> + * Copyright (c) 2023 Carsten Spieß <mail@carsten-spiess.de>
> + */
> +
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/slab.h>
> +#include <linux/i2c.h>
> +#include <linux/hwmon.h>
> +#include <linux/hwmon-sysfs.h>
> +#include <linux/debugfs.h>
> +#include <linux/err.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +#include <linux/util_macros.h>
> +#include <linux/regulator/consumer.h>
> +
> +/* ISL28022 registers */
> +#define ISL28022_REG_CONFIG 0x00
> +#define ISL28022_REG_SHUNT 0x01
> +#define ISL28022_REG_BUS 0x02
> +#define ISL28022_REG_POWER 0x03
> +#define ISL28022_REG_CURRENT 0x04
> +#define ISL28022_REG_CALIB 0x05
> +#define ISL28022_REG_SHUNT_THR 0x06
> +#define ISL28022_REG_BUS_THR 0x07
> +#define ISL28022_REG_INT 0x08
> +#define ISL28022_REG_AUX 0x09
> +#define ISL28022_REG_MAX ISL28022_REG_AUX
> +
> +/* ISL28022 config flags */
> +/* mode flags */
> +#define ISL28022_MODE_SHIFT 0
> +#define ISL28022_MODE_MASK 0x0007
> +
> +#define ISL28022_MODE_PWR_DOWN 0x0
> +#define ISL28022_MODE_TRG_S 0x1
> +#define ISL28022_MODE_TRG_B 0x2
> +#define ISL28022_MODE_TRG_SB 0x3
> +#define ISL28022_MODE_ADC_OFF 0x4
> +#define ISL28022_MODE_CONT_S 0x5
> +#define ISL28022_MODE_CONT_B 0x6
> +#define ISL28022_MODE_CONT_SB 0x7
> +
> +/* shunt ADC settings */
> +#define ISL28022_SADC_SHIFT 3
> +#define ISL28022_SADC_MASK 0x0078
> +
> +#define ISL28022_BADC_SHIFT 7
> +#define ISL28022_BADC_MASK 0x0780
> +
> +#define ISL28022_ADC_12 0x0 /* 12 bit ADC */
> +#define ISL28022_ADC_13 0x1 /* 13 bit ADC */
> +#define ISL28022_ADC_14 0x2 /* 14 bit ADC */
> +#define ISL28022_ADC_15 0x3 /* 15 bit ADC */
> +#define ISL28022_ADC_15_1 0x8 /* 15 bit ADC, 1 sample */
> +#define ISL28022_ADC_15_2 0x9 /* 15 bit ADC, 2 samples */
> +#define ISL28022_ADC_15_4 0xA /* 15 bit ADC, 4 samples */
> +#define ISL28022_ADC_15_8 0xB /* 15 bit ADC, 8 samples */
> +#define ISL28022_ADC_15_16 0xC /* 15 bit ADC, 16 samples */
> +#define ISL28022_ADC_15_32 0xD /* 15 bit ADC, 32 samples */
> +#define ISL28022_ADC_15_64 0xE /* 15 bit ADC, 64 samples */
> +#define ISL28022_ADC_15_128 0xF /* 15 bit ADC, 128 samples */
> +
> +/* shunt voltage range */
> +#define ISL28022_PG_SHIFT 11
> +#define ISL28022_PG_MASK 0x1800
> +
> +#define ISL28022_PG_40 0x0 /* +/-40 mV */
> +#define ISL28022_PG_80 0x1 /* +/-80 mV */
> +#define ISL28022_PG_160 0x2 /* +/-160 mV */
> +#define ISL28022_PG_320 0x3 /* +/-3200 mV */
> +
> +/* bus voltage range */
> +#define ISL28022_BRNG_SHIFT 13
> +#define ISL28022_BRNG_MASK 0x6000
> +
> +#define ISL28022_BRNG_16 0x0 /* 16 V */
> +#define ISL28022_BRNG_32 0x1 /* 32 V */
> +#define ISL28022_BRNG_60 0x3 /* 60 V */
> +
> +/* reset */
> +#define ISL28022_RESET 0x8000
> +
> +struct isl28022_data {
> + struct i2c_client *client;
> + struct regmap *regmap;
> +#ifdef CONFIG_DEBUG_FS
> + struct dentry *debugfs;
> +#endif
> + u32 shunt;
> + u32 gain;
> + u32 average;
> + u16 config;
> + u16 calib;
> +};
> +
> +static int isl28022_read(struct device *dev, enum hwmon_sensor_types type,
> + u32 attr, int channel, long *val)
> +{
> + struct isl28022_data *data = dev_get_drvdata(dev);
> + unsigned int regval;
> + int err;
> +
> + switch (type) {
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + err = regmap_read(data->regmap,
> + ISL28022_REG_BUS, &regval);
> + if (err < 0)
> + return err;
> + /* driver supports only 60V mode (BRNG 11) */
> + *val = (long)(((u16)regval) & 0xFFFC);
> + break;
> + default:
> + return -EINVAL;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + err = regmap_read(data->regmap,
> + ISL28022_REG_CURRENT, &regval);
> + if (err < 0)
> + return err;
> + *val = ((long)regval * 1250L * (long)data->gain) /
> + (long)data->shunt;
> + break;
> + default:
> + return -EINVAL;
> + }
> + break;
> + case hwmon_power:
> + switch (attr) {
> + case hwmon_power_input:
> + err = regmap_read(data->regmap,
> + ISL28022_REG_POWER, &regval);
> + if (err < 0)
> + return err;
> + *val = ((51200000L * ((long)data->gain)) /
> + (long)data->shunt) * (long)regval;
> + break;
> + default:
> + return -EINVAL;
> + }
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static umode_t isl28022_is_visible(const void *data, enum hwmon_sensor_types type,
> + u32 attr, int channel)
> +{
> + switch (type) {
> + case hwmon_in:
> + switch (attr) {
> + case hwmon_in_input:
> + return 0444;
> + }
> + break;
> + case hwmon_curr:
> + switch (attr) {
> + case hwmon_curr_input:
> + return 0444;
> + }
> + break;
> + case hwmon_power:
> + switch (attr) {
> + case hwmon_power_input:
> + return 0444;
> + }
> + break;
> + default:
> + break;
> + }
> + return 0;
> +}
> +
> +static const struct hwmon_channel_info *isl28022_info[] = {
> + HWMON_CHANNEL_INFO(in,
> + HWMON_I_INPUT), /* channel 0: bus voltage (mV) */
> + HWMON_CHANNEL_INFO(curr,
> + HWMON_C_INPUT), /* channel 1: current (mA) */
> + HWMON_CHANNEL_INFO(power,
> + HWMON_P_INPUT), /* channel 1: power (µW) */
> + NULL
> +};
> +
> +static const struct hwmon_ops isl28022_hwmon_ops = {
> + .is_visible = isl28022_is_visible,
> + .read = isl28022_read,
> +};
> +
> +static const struct hwmon_chip_info isl28022_chip_info = {
> + .ops = &isl28022_hwmon_ops,
> + .info = isl28022_info,
> +};
> +
> +static bool isl28022_is_writeable_reg(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case ISL28022_REG_CONFIG:
> + case ISL28022_REG_CALIB:
> + case ISL28022_REG_SHUNT_THR:
> + case ISL28022_REG_BUS_THR:
> + case ISL28022_REG_INT:
> + case ISL28022_REG_AUX:
> + return true;
> + }
> +
> + return false;
> +}
> +
> +static bool isl28022_is_volatile_reg(struct device *dev, unsigned int reg)
> +{
> + switch (reg) {
> + case ISL28022_REG_CONFIG:
> + case ISL28022_REG_SHUNT:
> + case ISL28022_REG_BUS:
> + case ISL28022_REG_POWER:
> + case ISL28022_REG_CURRENT:
> + case ISL28022_REG_INT:
> + case ISL28022_REG_AUX:
> + return true;
> + }
> + return true;
> +}
> +
> +static const struct regmap_config isl28022_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 16,
> + .max_register = ISL28022_REG_MAX,
> + .writeable_reg = isl28022_is_writeable_reg,
> + .volatile_reg = isl28022_is_volatile_reg,
> + .val_format_endian = REGMAP_ENDIAN_BIG,
> + .cache_type = REGCACHE_RBTREE,
> + .use_single_read = true,
> + .use_single_write = true,
> +};
> +
> +static const struct i2c_device_id isl28022_ids[] = {
> + { "isl28022", 0},
> + { /* LIST END */ }
> +};
> +MODULE_DEVICE_TABLE(i2c, isl28022_ids);
> +
> +#ifdef CONFIG_DEBUG_FS
> +static int shunt_voltage_show(struct seq_file *seqf, void *unused)
> +{
> + struct isl28022_data *data = seqf->private;
> + unsigned int regval;
> + int err;
> +
> + err = regmap_read(data->regmap,
> + ISL28022_REG_SHUNT, &regval);
> + if (err)
> + return err;
> +
> + /* print shunt voltage in micro volt */
> + seq_printf(seqf, "%d\n", regval * 10);
> +
> + return 0;
> +}
> +DEFINE_SHOW_ATTRIBUTE(shunt_voltage);
> +
> +static struct dentry *isl28022_debugfs_root;
> +
> +static void isl28022_debugfs_remove(void *res)
> +{
> + debugfs_remove_recursive(res);
> +}
> +
> +static int isl28022_debugfs_init(struct isl28022_data *data)
> +{
> + char name[16];
> + int err;
> + struct dentry *entry;
> +
> + scnprintf(name, sizeof(name), "%d-%04hx", data->client->adapter->nr, data->client->addr);
> +
> + data->debugfs = debugfs_create_dir(name, isl28022_debugfs_root);
> + if (IS_ERR(data->debugfs))
> + return PTR_ERR(data->debugfs);
> +
> + err = devm_add_action_or_reset(&data->client->dev, isl28022_debugfs_remove, data->debugfs);
> + if (err)
> + return err;
> +
> + entry = debugfs_create_file("shunt_voltage", 0444, data->debugfs, data,
> + &shunt_voltage_fops);
> + if (IS_ERR(entry))
> + return PTR_ERR(entry);
> +
> + return 0;
> +}
> +#endif /* CONFIG_DEBUG_FS*/
> +
> +/*
> + * read property values and make consistency checks.
> + *
> + * following values for shunt range and resistor are allowed:
> + * 40 mV -> gain 1, shunt min. 800 micro ohms
> + * 80 mV -> gain 2, shunt min. 1600 micro ohms
> + * 160 mV -> gain 4, shunt min. 3200 micro ohms
> + * 320 mV -> gain 8, shunt min. 6400 micro ohms
> + */
> +static int isl28022_read_properties(struct device *dev, struct isl28022_data *data)
> +{
> + u32 val;
> + int err;
> +
> + err = device_property_read_u32(dev, "shunt-resistor-micro-ohms", &val);
> + if (err == -ENODATA)
> + val = 10000;
> + else if (err < 0)
> + return err;
> + data->shunt = val;
> +
> + err = device_property_read_u32(dev, "renesas,shunt-range-microvolt", &val);
> + if (err == -ENODATA)
> + val = 320000;
> + else if (err < 0)
> + return err;
> + switch (val) {
> + case 40000:
> + data->gain = 1;
> + if (data->shunt < 800)
> + goto shunt_invalid;
> + break;
> + case 80000:
> + data->gain = 2;
> + if (data->shunt < 1600)
> + goto shunt_invalid;
> + break;
> + case 160000:
> + data->gain = 4;
> + if (data->shunt < 3200)
> + goto shunt_invalid;
> + break;
> + case 320000:
> + data->gain = 8;
> + if (data->shunt < 6400)
> + goto shunt_invalid;
> + break;
> + default:
> + dev_err(dev, "renesas,shunt-range-microvolt invalid value %d\n", val);
> + return -EINVAL;
> + }
> +
> + err = device_property_read_u32(dev, "renesas,average-samples", &val);
> + if (err == -ENODATA)
> + val = 1;
> + else if (err < 0)
> + return err;
> + if ((val > 128) || (BIT(__ffs(val)) != val)) {
> + dev_err(dev, "renesas,average-samples invalid value %d\n", val);
> + return -EINVAL;
> + }
> + data->average = val;
> +
> + return 0;
> +
> +shunt_invalid:
> + dev_err(dev, "renesas,shunt-resistor-microvolt invalid value %d\n", data->shunt);
> + return -EINVAL;
> +}
> +
> +/*
> + * write configuration and calibration registers
> + *
> + * The driver supports only shunt and bus continuous ADC mode at 15bit resolution
> + * with averaging from 1 to 128 samples (pow of 2) on both channels.
> + * Shunt voltage gain 1,2,4 or 8 is allowed.
> + * The bus voltage range is 60V fixed.
> + */
> +static int isl28022_config(struct isl28022_data *data)
> +{
> + int err;
> +
> + data->config = (ISL28022_MODE_CONT_SB << ISL28022_MODE_SHIFT) |
> + (ISL28022_BRNG_60 << ISL28022_BRNG_SHIFT) |
> + (__ffs(data->gain) << ISL28022_PG_SHIFT) |
> + ((ISL28022_ADC_15_1 + __ffs(data->average)) << ISL28022_SADC_SHIFT) |
> + ((ISL28022_ADC_15_1 + __ffs(data->average)) << ISL28022_BADC_SHIFT);
> +
> + data->calib = data->shunt ? 0x8000 / data->gain : 0;
> +
> + err = regmap_write(data->regmap, ISL28022_REG_CONFIG, data->config);
> + if (err < 0)
> + return err;
> +
> + err = regmap_write(data->regmap, ISL28022_REG_CALIB, data->calib);
> + if (err < 0)
> + return err;
> +
> + return 0;
> +}
> +
> +static int isl28022_probe(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct device *hwmon_dev;
> + struct isl28022_data *data;
> + int err;
> +
> + if (!i2c_check_functionality(client->adapter,
> + I2C_FUNC_SMBUS_BYTE_DATA |
> + I2C_FUNC_SMBUS_WORD_DATA))
> + return -ENODEV;
> +
> + data = devm_kzalloc(dev, sizeof(struct isl28022_data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + data->client = client;
> +
> + err = isl28022_read_properties(dev, data);
> + if (err)
> + return err;
> +
> + data->regmap = devm_regmap_init_i2c(client, &isl28022_regmap_config);
> + if (IS_ERR(data->regmap))
> + return PTR_ERR(data->regmap);
> +
> + err = isl28022_config(data);
> + if (err)
> + return err;
> +
> +#ifdef CONFIG_DEBUG_FS
> + err = isl28022_debugfs_init(data);
> + if (err)
> + return err;
> +#endif
> +
> + hwmon_dev = devm_hwmon_device_register_with_info(dev, "isl28022_hwmon",
> + data, &isl28022_chip_info, NULL);
> + if (IS_ERR(hwmon_dev))
> + return PTR_ERR(hwmon_dev);
> +
> + dev_info(dev, "%s: sensor '%s'\n", dev_name(hwmon_dev), client->name);
> + return 0;
> +}
> +
> +static const struct of_device_id __maybe_unused isl28022_of_match[] = {
> + { .compatible = "renesas,isl28022"},
> + { /* LIST END */ }
> +};
> +MODULE_DEVICE_TABLE(of, isl28022_of_match);
> +
> +static struct i2c_driver isl28022_driver = {
> + .class = I2C_CLASS_HWMON,
> + .driver = {
> + .name = "isl28022",
> + },
> + .probe_new = isl28022_probe,
> + .id_table = isl28022_ids,
> +};
> +
> +#ifdef CONFIG_DEBUG_FS
> +static int __init
> +isl28022_init(void)
> +{
> + int err;
> +
> + isl28022_debugfs_root = debugfs_create_dir("isl28022", NULL);
> + err = i2c_add_driver(&isl28022_driver);
> + if (!err)
> + return 0;
> +
> + debugfs_remove_recursive(isl28022_debugfs_root);
> + return err;
> +}
> +
> +static void __exit
> +isl28022_exit(void)
> +{
> + i2c_del_driver(&isl28022_driver);
> + debugfs_remove_recursive(isl28022_debugfs_root);
> +}
> +
> +module_init(isl28022_init);
> +module_exit(isl28022_exit);
> +#else /* CONFIG_DEBUG_FS */
> +module_i2c_driver(isl28022_driver);
> +#endif /* CONFIG_DEBUG_FS */
> +
> +MODULE_AUTHOR("Carsten Spieß <mail@carsten-spiess.de>");
> +MODULE_DESCRIPTION("ISL28022 driver");
> +MODULE_LICENSE("GPL");

\
 
 \ /
  Last update: 2023-07-28 11:42    [W:0.043 / U:1.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site