lkml.org 
[lkml]   [2023]   [Jun]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v1 3/5] mm/memory_hotplug: make offline_and_remove_memory() timeout instead of failing on fatal signals
On 27.06.23 16:17, Michal Hocko wrote:
> On Tue 27-06-23 15:14:11, David Hildenbrand wrote:
>> On 27.06.23 14:40, Michal Hocko wrote:
>>> On Tue 27-06-23 13:22:18, David Hildenbrand wrote:
>>>> John Hubbard writes [1]:
>>>>
>>>> Some device drivers add memory to the system via memory hotplug.
>>>> When the driver is unloaded, that memory is hot-unplugged.
>>>>
>>>> However, memory hot unplug can fail. And these days, it fails a
>>>> little too easily, with respect to the above case. Specifically, if
>>>> a signal is pending on the process, hot unplug fails.
>>>>
>>>> [...]
>>>>
>>>> So in this case, other things (unmovable pages, un-splittable huge
>>>> pages) can also cause the above problem. However, those are
>>>> demonstrably less common than simply having a pending signal. I've
>>>> got bug reports from users who can trivially reproduce this by
>>>> killing their process with a "kill -9", for example.
>>>
>>> This looks like a bug of the said driver no? If the tear down process is
>>> killed it could very well happen right before offlining so you end up in
>>> the very same state. Or what am I missing?
>>
>> IIUC (John can correct me if I am wrong):
>>
>> 1) The process holds the device node open
>> 2) The process gets killed or quits
>> 3) As the process gets torn down, it closes the device node
>> 4) Closing the device node results in the driver removing the device and
>> calling offline_and_remove_memory()
>>
>> So it's not a "tear down process" that triggers that offlining_removal
>> somehow explicitly, it's just a side-product of it letting go of the device
>> node as the process gets torn down.
>
> Isn't that just fragile? The operation might fail for other reasons. Why
> cannot there be a hold on the resource to control the tear down
> explicitly?

I'll let John comment on that. But from what I understood, in most
setups where ZONE_MOVABLE gets used for hotplugged memory
offline_and_remove_memory() succeeds and allows for reusing the device
later without a reboot.

For the cases where it doesn't work, a reboot is required.

>
>>>> Especially with ZONE_MOVABLE, offlining is supposed to work in most
>>>> cases when offlining actually hotplugged (not boot) memory, and only fail
>>>> in rare corner cases (e.g., some driver holds a reference to a page in
>>>> ZONE_MOVABLE, turning it unmovable).
>>>>
>>>> In these corner cases we really don't want to be stuck forever in
>>>> offline_and_remove_memory(). But in the general cases, we really want to
>>>> do our best to make memory offlining succeed -- in a reasonable
>>>> timeframe.
>>>>
>>>> Reliably failing in the described case when there is a fatal signal pending
>>>> is sub-optimal. The pending signal check is mostly only relevant when user
>>>> space explicitly triggers offlining of memory using sysfs device attributes
>>>> ("state" or "online" attribute), but not when coming via
>>>> offline_and_remove_memory().
>>>>
>>>> So let's use a timer instead and ignore fatal signals, because they are
>>>> not really expressive for offline_and_remove_memory() users. Let's default
>>>> to 30 seconds if no timeout was specified, and limit the timeout to 120
>>>> seconds.
>>>
>>> I really hate having timeouts back. They just proven to be hard to get
>>> right and it is essentially a policy implemented in the kernel. They
>>> simply do not belong to the kernel space IMHO.
>>
>> As much as I agree with you in terms of offlining triggered from user space
>> (e.g., write "state" or "online" attribute) where user-space is actually in
>> charge and can do something reasonable (timeout, retry, whatever), in these
>> the offline_and_remove_memory() case it's the driver that wants a
>> best-effort memory offlining+removal.
>>
>> If it times out, virtio-mem will simply try another block or retry later.
>> Right now, it could get stuck forever in offline_and_remove_memory(), which
>> is obviously "not great". Fortunately, for virtio-mem it's configurable and
>> we use the alloc_contig_range()-method for now as default.
>
> It seems that offline_and_remove_memory is using a wrong operation then.
> If it wants an opportunistic offlining with some sort of policy. Timeout
> might be just one policy to use but failure mode or a retry count might
> be a better fit for some users. So rather than (ab)using offline_pages,
> would be make more sense to extract basic offlining steps and allow
> drivers like virtio-mem to reuse them and define their own policy?

virtio-mem, in default operation, does that: use alloc_contig_range() to
logically unplug ("fake offline") that memory and then just trigger
offline_and_remove_memory() to make it "officially offline".

In that mode, offline_and_remove_memory() cannot really timeout and is
almost always going to succeed (except memory notifiers and some hugetlb
dissolving).

Right now we also allow the admin to configure ordinary offlining
directly (without prior fake offlining) when bigger memory blocks are
used: offline_pages() is more reliable than alloc_contig_range(), for
example, because it disables the PCP and the LRU cache, and retries more
often (well, unfortunately then also forever). It has a higher chance of
succeeding especially when bigger blocks of memory are offlined+removed.

Maybe we should make the alloc_contig_range()-based mechanism more
configurable and make it the only mode in virtio-mem, such that we don't
have to mess with offline_and_remove_memory() endless loops -- at least
for virtio-mem.

>
>> If it would time out for John's driver, we most certainly don't want to be
>> stuck in offline_and_remove_memory(), blocking device/driver unloading (and
>> even a reboot IIRC) possibly forever.
>
> Now I am confused. John driver wants to tear down the device now? There
> is no way to release that memory otherwise AFAIU from the initial
> problem description.

From what I understood if offline_and_remove_memory() succeeded, the
device can be reinitialized and used again. Otherwise, a reboot is
required because that memory is still added to the system.

Thanks Michal!

--
Cheers,

David / dhildenb

\
 
 \ /
  Last update: 2023-06-27 16:59    [W:0.064 / U:1.348 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site