Messages in this thread | | | Date | Mon, 22 May 2023 11:38:43 -0700 | Subject | Re: [PATCH v3 5/5] drm/msm/dsi: Remove incorrect references to slice_count | From | Jessica Zhang <> |
| |
On 5/20/2023 5:32 PM, Dmitry Baryshkov wrote: > On 20/05/2023 00:17, Jessica Zhang wrote: >> Currently, slice_count is being used to calculate word count and >> pkt_per_line. In downstream, these values are calculated using slice per >> packet, which is not the same as slice_count. > > I'd say the reference to downstream is not correct. We have seen cases > where the vendor kernel contained errors. So it should be something like > "Instead these values should be calculated using ...."
Hi Dmitry,
Acked.
Thanks,
Jessica Zhang
> >> >> Slice count represents the number of soft slices per interface, and its >> value will not always match that of slice per packet. For example, it is >> possible to have cases where there are multiple soft slices per interface >> but the panel specifies only one slice per packet. >> >> Thus, use the default value of one slice per packet and remove >> slice_count >> from the aforementioned calculations. >> >> Fixes: 08802f515c3c ("drm/msm/dsi: Add support for DSC configuration") >> Fixes: bc6b6ff8135c ("drm/msm/dsi: Use DSC slice(s) packet size to >> compute word count") >> Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com> >> --- >> drivers/gpu/drm/msm/dsi/dsi_host.c | 24 ++++++++++++++---------- >> 1 file changed, 14 insertions(+), 10 deletions(-) >> >> diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c >> b/drivers/gpu/drm/msm/dsi/dsi_host.c >> index d04f8bbd707d..8c8858ee59ec 100644 >> --- a/drivers/gpu/drm/msm/dsi/dsi_host.c >> +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c >> @@ -866,18 +866,15 @@ static void dsi_update_dsc_timing(struct >> msm_dsi_host *msm_host, bool is_cmd_mod >> */ >> slice_per_intf = msm_dsc_get_slices_per_intf(dsc, hdisplay); >> - /* >> - * If slice_count is greater than slice_per_intf >> - * then default to 1. This can happen during partial >> - * update. >> - */ >> - if (dsc->slice_count > slice_per_intf) >> - dsc->slice_count = 1; >> - >> total_bytes_per_intf = dsc->slice_chunk_size * slice_per_intf; >> eol_byte_num = total_bytes_per_intf % 3; >> - pkt_per_line = slice_per_intf / dsc->slice_count; >> + >> + /* >> + * Default to 1 slice_per_pkt, so pkt_per_line will be equal to >> + * slice per intf. >> + */ >> + pkt_per_line = slice_per_intf; >> if (is_cmd_mode) /* packet data type */ >> reg = >> DSI_COMMAND_COMPRESSION_MODE_CTRL_STREAM0_DATATYPE(MIPI_DSI_DCS_LONG_WRITE); >> @@ -1001,7 +998,14 @@ static void dsi_timing_setup(struct msm_dsi_host >> *msm_host, bool is_bonded_dsi) >> if (!msm_host->dsc) >> wc = hdisplay * dsi_get_bpp(msm_host->format) / 8 + 1; >> else >> - wc = msm_host->dsc->slice_chunk_size * >> msm_host->dsc->slice_count + 1; >> + /* >> + * When DSC is enabled, WC = slice_chunk_size * >> slice_per_packet + 1. >> + * Currently, the driver only supports default value of >> slice_per_packet = 1 >> + * >> + * TODO: Expand mipi_dsi_device struct to hold >> slice_per_packet info >> + * and adjust DSC math to account for >> slice_per_packet. >> + */ >> + wc = msm_host->dsc->slice_chunk_size + 1; >> dsi_write(msm_host, REG_DSI_CMD_MDP_STREAM0_CTRL, >> DSI_CMD_MDP_STREAM0_CTRL_WORD_COUNT(wc) | >> > > -- > With best wishes > Dmitry >
| |