lkml.org 
[lkml]   [2023]   [Apr]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRE: [PATCH v2 4/4] spi: cadence-quadspi: use STIG mode for small reads
From
Hi Yoshitaka,

On 26/04/23 08:04, Yoshitaka Ikeda wrote:
> Hi Dhruva,
>
> An error occurred in the following environments where this patch was applied, and the flash could not be accessed.
> However, after reverting to this patch, it is possible to access it.
>
> - Environment
> - OS : Linux 6.3
> - SoC : Cyclone V

Please can you send me the register fields information for the
CQSPI controller used in this device?
I wanted to verify if atall there were any mismatch between the
controller I have tested with vs your SOC's controller.

> - Flash : MT25QL512A
>
> - Error at startup
> - Kernel log
> [ 0.980290] spi-nor spi0.0: found mt25ql512a, expected n25q512a
> [ 1.485140] cadence-qspi ff705000.flash: Flash command execution timed out.
> [ 1.490792] spi-nor spi0.0: operation failed with -110
> [ 1.494654] spi-nor spi0.0: mt25ql512a (65536 Kbytes)
>
> - Error at access
> - Access command and log
> # hexdump -Cv /dev/mtdblock0
> hexdump: /dev/mtdblock0: Input/output error
>
> - Kernel log
> [ 2124.201193] cadence-qspi ff705000.flash: QSPI is still busy after 500ms timeout.
> [ 2124.201229] spi-nor spi0.0: operation failed with -110
> [ 2124.201256] I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
> [ 2124.711241] cadence-qspi ff705000.flash: QSPI is still busy after 500ms timeout.
> [ 2124.711276] spi-nor spi0.0: operation failed with -110
> [ 2124.711302] I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
> [ 2125.221193] cadence-qspi ff705000.flash: QSPI is still busy after 500ms timeout.
> [ 2125.221230] spi-nor spi0.0: operation failed with -110
> [ 2125.221256] I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
> [ 2125.731237] cadence-qspi ff705000.flash:. QSPI is still busy after 500ms timeout.
> [ 2125.731270] spi-nor spi0.0: operation failed with -110
> [ 2125.731296] I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
> [ 2126.241190] cadence-qspi ff705000.flash:. QSPI is still busy after 500ms timeout.
> [ 2126.241224] spi-nor spi0.0: operation failed with -110
> [ 2126.241251] I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
> [ 2126.241274] Buffer I/O error on dev mtdblock0, logical block 0, async page read
>
>
> regards,
> Yoshitaka Ikeda
>
>
> [..snip..]

It maybe that STIG mode may have some different way of configuring/using
on your SoC.

However at this point it's only a guess and I will wait till I have the
exact information on the controller specs being used in this device
along with the register descriptions.

--
Thanks and Regards,
Dhruva Gole

\
 
 \ /
  Last update: 2023-04-26 09:40    [W:0.078 / U:0.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site