lkml.org 
[lkml]   [2023]   [Apr]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform
On Thu, 13 Apr 2023, Sherry Sun wrote:

> For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM.
> So here should configure the corresponding UARTMODIR register bits.
>
> Fixes: 67b01837861c ("tty: serial: lpuart: Add RS485 support for 32-bit uart flavour")

The patch is good but I don't think Fixes tag is warranted here because
TXRTSPOL and TXRTSE bits are the same for both registers. ...So this
is mostly to avoid reader confusion rather than fix an actual problem.

Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

--
i.

> Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
> ---
> drivers/tty/serial/fsl_lpuart.c | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
> index 074bfed57fc9..9845d3f5b84b 100644
> --- a/drivers/tty/serial/fsl_lpuart.c
> +++ b/drivers/tty/serial/fsl_lpuart.c
> @@ -1406,12 +1406,12 @@ static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termio
> struct lpuart_port, port);
>
> unsigned long modem = lpuart32_read(&sport->port, UARTMODIR)
> - & ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
> + & ~(UARTMODIR_TXRTSPOL | UARTMODIR_TXRTSE);
> lpuart32_write(&sport->port, modem, UARTMODIR);
>
> if (rs485->flags & SER_RS485_ENABLED) {
> /* Enable auto RS-485 RTS mode */
> - modem |= UARTMODEM_TXRTSE;
> + modem |= UARTMODIR_TXRTSE;
>
> /*
> * The hardware defaults to RTS logic HIGH while transfer.
> @@ -1420,9 +1420,9 @@ static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termio
> * Note: UART is assumed to be active high.
> */
> if (rs485->flags & SER_RS485_RTS_ON_SEND)
> - modem |= UARTMODEM_TXRTSPOL;
> + modem |= UARTMODIR_TXRTSPOL;
> else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
> - modem &= ~UARTMODEM_TXRTSPOL;
> + modem &= ~UARTMODIR_TXRTSPOL;
> }
>
> lpuart32_write(&sport->port, modem, UARTMODIR);
>
\
 
 \ /
  Last update: 2023-04-13 19:05    [W:0.028 / U:0.524 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site