Messages in this thread | | | Date | Thu, 9 Mar 2023 18:25:09 +0100 | From | Johan Hovold <> | Subject | Re: [PATCH v5 4/4] arm64: dts: qcom: thinkpad-x13s: Add bluetooth |
| |
On Wed, Feb 08, 2023 at 08:09:16PM -0600, Steev Klimaszewski wrote: > The Lenovo Thinkpad X13s has a WCN6855 Bluetooth controller on uart2, > add this. > > Signed-off-by: Steev Klimaszewski <steev@kali.org> > Link: https://lore.kernel.org/r/20230207052829.3996-5-steev@kali.org
This link should not be needed.
Also, please update the patch Subject to use the following prefix:
arm64: dts: qcom: sc8280xp-x13s: ...
> --- > Changes since v4: > * Address Konrad's review comments. > > Changes since v3: > * Add vreg_s1c > * Add regulators and not dead code > * Fix commit message changelog > > Changes since v2: > * Remove dead code and add TODO comment > * Make dtbs_check happy with the pin definitions > .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 76 +++++++++++++++++++ > 1 file changed, 76 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > index f936b020a71d..ad20cfb3a830 100644 > --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > @@ -24,6 +24,8 @@ / { > aliases { > i2c4 = &i2c4; > i2c21 = &i2c21; > + serial0 = &uart17;
This is an unrelated change that does not belong in this patch.
> + serial1 = &uart2; > }; > > wcd938x: audio-codec { > @@ -297,6 +299,15 @@ pmc8280c-rpmh-regulators { > qcom,pmic-id = "c"; > vdd-bob-supply = <&vreg_vph_pwr>; > > + vreg_s1c: smps1 { > + regulator-name = "vreg_s1c"; > + regulator-min-microvolt = <1880000>; > + regulator-max-microvolt = <1900000>; > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_AUTO>, > + <RPMH_REGULATOR_MODE_RET>; > + regulator-allow-set-load;
Don't you need to specify initial-mode as well?
> + }; > + > vreg_l1c: ldo1 { > regulator-name = "vreg_l1c"; > regulator-min-microvolt = <1800000>; > @@ -712,6 +723,32 @@ &qup0 { > status = "okay"; > }; > > +&uart2 { > + pinctrl-0 = <&uart2_state>; > + pinctrl-names = "default"; > + > + status = "okay"; > + > + bluetooth { > + compatible = "qcom,wcn6855-bt"; > + > + vddio-supply = <&vreg_s10b>; > + vddbtcxmx-supply = <&vreg_s12b>; > + vddrfacmn-supply = <&vreg_s12b>; > + vddrfa0p8-supply = <&vreg_s12b>; > + vddrfa1p2-supply = <&vreg_s11b>; > + vddrfa1p7-supply = <&vreg_s1c>; > + > + max-speed = <3200000>; > + > + enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>; > + swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&bt_en>; > + pinctrl-names = "default"; > + }; > +}; > + > &qup1 { > status = "okay"; > }; > @@ -720,6 +757,11 @@ &qup2 { > status = "okay"; > }; > > +&uart17 { > + compatible = "qcom,geni-debug-uart"; > + status = "okay"; > +};
This bit does not belong here either. We don't have any means of accessing the debug uart on the X13s so we should probably just leave it disabled.
> + > &remoteproc_adsp { > firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn"; > > @@ -980,6 +1022,19 @@ hastings_reg_en: hastings-reg-en-state { > &tlmm { > gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; > > + bt_en: bt-en-state {
As you are configuring more than one pin, please rename this as:
bt_default: bt-default-state
> + hstp-sw-ctrl-pins { > + pins = "gpio132"; > + function = "gpio";
You should define the bias configuration as well. I guess we need to keep the default pull-down enabled.
> + }; > + > + hstp-bt-en-pins { > + pins = "gpio133"; > + function = "gpio"; > + drive-strength = <16>;
bias-disable?
> + }; > + }; > + > edp_reg_en: edp-reg-en-state { > pins = "gpio25"; > function = "gpio"; > @@ -1001,6 +1056,27 @@ i2c4_default: i2c4-default-state { > bias-disable; > }; > > + uart2_state: uart2-state {
Rename this one too:
uart2_default: uart2-default-state
> + cts-pins { > + pins = "gpio122";
This should be gpio121 (gpio122 is rts).
> + function = "qup2"; > + bias-disable;
Don't we need a pull-down on this one to avoid a floating input when the module is powered down?
> + }; > + > + rts-tx-pins {
Please split this in two nodes.
> + pins = "gpio122", "gpio123"; > + function = "qup2"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + rx-pins { > + pins = "gpio124"; > + function = "qup2"; > + bias-pull-up; > + }; > + }; > + > i2c21_default: i2c21-default-state { > pins = "gpio81", "gpio82"; > function = "qup21";
Johan
| |