lkml.org 
[lkml]   [2023]   [Mar]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v4 17/19] thermal/tegra: Do not enable the thermal zone, it is already enabled
From
On 01/03/2023 15:29, Thierry Reding wrote:
> On Tue, Feb 28, 2023 at 12:22:36PM +0100, Daniel Lezcano wrote:
>> The code enables the thermal zone after setting it up. But the thermal
>> zone is already enabled by thermal_of_zone_register() function.
>>
>> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
>> ---
>> drivers/thermal/tegra/tegra30-tsensor.c | 8 +-------
>> 1 file changed, 1 insertion(+), 7 deletions(-)
>>
>> diff --git a/drivers/thermal/tegra/tegra30-tsensor.c b/drivers/thermal/tegra/tegra30-tsensor.c
>> index 3506c3f3c474..e38902abf207 100644
>> --- a/drivers/thermal/tegra/tegra30-tsensor.c
>> +++ b/drivers/thermal/tegra/tegra30-tsensor.c
>> @@ -346,7 +346,7 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
>> {
>> const struct tegra_tsensor_channel *tsc = &ts->ch[id];
>> struct thermal_zone_device *tzd = tsc->tzd;
>> - int err, hot_trip = 0, crit_trip = 0;
>> + int hot_trip = 0, crit_trip = 0;
>> u32 val;
>>
>> if (!tzd) {
>> @@ -401,12 +401,6 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
>> val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_INTR_THERMAL_RST_EN, 1);
>> writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG0);
>>
>> - err = thermal_zone_device_enable(tzd);
>> - if (err) {
>> - dev_err(ts->dev, "ch%u: failed to enable zone: %d\n", id, err);
>> - return err;
>> - }
>> -
>> return 0;
>> }
>
> This function is called in tegra_tsensor_resume() and balances out the
> tegra_tsensor_hw_channel() calls from tegra_tsensor_suspend(). If we
> remove the call from here, we'll likely end up with the zones disabled
> after a resume.
>
> This ends up calling thermal_zone_device_set_mode(), which is a no-op,
> basically, if the mode is unchanged, so this seems harmless.
>
> If you need this to change anyway, I suppose we could move the calls to
> thermal_zone_device_enable() and move them into suspend/resume instead.
> That's a bit tricky to undo in the error recovery paths, but should be
> doable.

No it is fine, I will just drop this patch from the series.


--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

\
 
 \ /
  Last update: 2023-03-27 00:40    [W:0.038 / U:0.320 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site