lkml.org 
[lkml]   [2023]   [Feb]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH V2 0/2] mmc: block: Support Host to control FUA
On Fri, 11 Nov 2022 at 13:04, Ulf Hansson <ulf.hansson@linaro.org> wrote:
>
> [...]
>
> > >
> > > Considering the data integrity, we did a random power-down test, and
> > > the experimental results were good.
> > >
> > > FUA can only reduce data loss under abnormal conditions, but cannot
> > > prevent data loss under abnormal conditions.
> > >
> > > I think there should be a balance between FUA and NO FUA, but
> > > filesystems seem to favor FUA.
> > >
> > > FUA brings a drop in random write performance. If enough tests are
> > > done, NO FUA is acceptable.
> >
> > Testing this isn't entirely easy. It requires you to hook up
> > electrical switches to allow you to automate the powering on/off of
> > the platform(s). Then at each cycle, really make sure to stress test
> > the data integrity of the flash memory. Is that what the tests did -
> > or can you elaborate a bit on what was really tested?
> >
> > In any case, the performance impact boils down to how each eMMC/SD
> > card internally manages reliable writes vs regular writes. Some
> > vendors may treat them very similarly, while others do not.
> >
> > That said, trying to disable REQ_FUA from an mmc host driver is the
> > wrong approach, as also pointed out by Adrian above. These types of
> > decisions belong solely in the mmc core layer.
> >
> > Instead of what the $subject series proposes, I would rather suggest
> > we discuss (and test) whether it could make sense to disable REQ_FUA -
> > *if* the eMMC/SD card supports a write-back-cache (REQ_OP_FLUSH) too.
> > Hence, the mmc core could then announce only REQ_OP_FLUSH.
> >
>
> Below is a simple patch that does the above. We may not want to enable
> this for *all* eMMC/SD cards, but it works fine for testing and to
> continue the discussions here.
>
>
> From: Ulf Hansson <ulf.hansson@linaro.org>
> Date: Fri, 11 Nov 2022 12:48:02 +0100
> Subject: [PATCH] mmc: core: Disable REQ_FUA if the card supports an internal
> cache
>
> !!!! This is not for merge, but only for test and discussions!!!
>
> It has been reported that REQ_FUA can be costly on some eMMC devices. A
> potential option that could mitigate this problem, is to rely solely on
> REQ_OP_FLUSH instead, but that requires the eMMC/SD to support an internal
> cache. This is an attempt to try this out to see how it behaves.
>
> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
> ---
> drivers/mmc/core/block.c | 10 +++++-----
> 1 file changed, 5 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c
> index db6d8a099910..197e9f6cdaad 100644
> --- a/drivers/mmc/core/block.c
> +++ b/drivers/mmc/core/block.c
> @@ -2494,15 +2494,15 @@ static struct mmc_blk_data
> *mmc_blk_alloc_req(struct mmc_card *card,
> md->flags |= MMC_BLK_CMD23;
> }
>
> - if (md->flags & MMC_BLK_CMD23 &&
> - ((card->ext_csd.rel_param & EXT_CSD_WR_REL_PARAM_EN) ||
> - card->ext_csd.rel_sectors)) {
> + if (mmc_cache_enabled(card->host)) {
> + cache_enabled = true;
> + } else if (md->flags & MMC_BLK_CMD23 &&
> + (card->ext_csd.rel_param & EXT_CSD_WR_REL_PARAM_EN ||
> + card->ext_csd.rel_sectors)) {
> md->flags |= MMC_BLK_REL_WR;
> fua_enabled = true;
> cache_enabled = true;
> }
> - if (mmc_cache_enabled(card->host))
> - cache_enabled = true;
>
> blk_queue_write_cache(md->queue.queue, cache_enabled, fua_enabled);
>
> --
> 2.34.1

Wenchao,

Did you manage to try the above patch to see if that could improve the
situation?

Kind regards
Uffe

\
 
 \ /
  Last update: 2023-03-27 00:16    [W:0.227 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site