lkml.org 
[lkml]   [2023]   [Feb]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC PATCH v8 3/3] selftests/x86: sysret_rip: Test SYSRET with a signal handler
Date
The current test_sigreturn_to() goes to the slow-path syscall with
IRET due to non-canonical addresses. It uses the SIGUSR1 signal to
perform the test.

Add a similar test that goes to the SYSRET path instead of IRET using
the SIGUSR2 signal. There are two cases:

A) 'syscall' in a FRED system preserves %rcx and %r11.

B) 'syscall' in a non-FRED system sets %rcx=%rip and %r11=%rflags.

The __raise(SIGUSR2) call verifies the 'syscall' behavior consistency
when dealing with a signal handler. It must always be (A) or always be
(B). Not a mix of them.

Cc: Xin Li <xin3.li@intel.com>
Link: https://lore.kernel.org/lkml/8770815f-0f23-d0c5-e56a-d401827842c9@zytor.com
Suggested-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
---
tools/testing/selftests/x86/sysret_rip.c | 30 ++++++++++++++++++++++++
1 file changed, 30 insertions(+)

diff --git a/tools/testing/selftests/x86/sysret_rip.c b/tools/testing/selftests/x86/sysret_rip.c
index 1531593b50d02150..746801675fe77e9c 100644
--- a/tools/testing/selftests/x86/sysret_rip.c
+++ b/tools/testing/selftests/x86/sysret_rip.c
@@ -274,6 +274,28 @@ static void test_syscall_rcx_r11_consistent(void)
do_syscall(__NR_getppid, 0, 0, 0, 0, 0, 0);
}

+static unsigned long usr2_rcx;
+static unsigned long usr2_r11;
+
+static void sigusr2(int sig, siginfo_t *info, void *ctx_void)
+{
+ ucontext_t *ctx = (ucontext_t*)ctx_void;
+
+ usr2_r11 = ctx->uc_mcontext.gregs[REG_R11];
+ usr2_rcx = ctx->uc_mcontext.gregs[REG_RCX];
+
+ check_regs_result(ctx->uc_mcontext.gregs[REG_R11],
+ ctx->uc_mcontext.gregs[REG_RCX],
+ ctx->uc_mcontext.gregs[REG_RBX]);
+}
+
+static void test_sysret_consistent(void)
+{
+ printf("[RUN]\ttest_sysret_consistent\n");
+ __raise(SIGUSR2);
+ printf("[OK]\tRCX = %#lx; R11 = %#lx\n", usr2_rcx, usr2_r11);
+}
+
int main()
{
int i;
@@ -291,6 +313,14 @@ int main()
for (i = 47; i < 64; i++)
test_sigreturn_to(1UL<<i);

+ /*
+ * test_sigreturn_to() above will test the IRET path. Now test
+ * the SYSRET path.
+ */
+ sethandler(SIGUSR2, sigusr2, 0);
+ for (i = 0; i < 32; i++)
+ test_sysret_consistent();
+
clearhandler(SIGUSR1);

sethandler(SIGSEGV, sigsegv_for_fallthrough, 0);
--
Ammar Faizi
\
 
 \ /
  Last update: 2023-03-27 00:28    [W:0.060 / U:0.300 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site