lkml.org 
[lkml]   [2023]   [Nov]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [RFC PATCH 5/5] arm64: dts: qcom: ipq9574: Add support for SPI nand
From


On 10/31/2023 8:57 PM, Konrad Dybcio wrote:
> On 31.10.2023 13:03, Md Sadre Alam wrote:
>> Add support for QPIC SPI NAND for IPQ9574
>>
>> Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
>> Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts | 56 ++++++++++-----------
>> arch/arm64/boot/dts/qcom/ipq9574.dtsi | 30 ++++++++++-
>> 2 files changed, 57 insertions(+), 29 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>> index 1bb8d96c9a82..5e4200edb873 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
>> @@ -15,48 +15,48 @@ / {
>> compatible = "qcom,ipq9574-ap-al02-c7", "qcom,ipq9574";
>> };
>>
>> -&sdhc_1 {
>> - pinctrl-0 = <&sdc_default_state>;
>> - pinctrl-names = "default";
>> - mmc-ddr-1_8v;
>> - mmc-hs200-1_8v;
>> - mmc-hs400-1_8v;
>> - mmc-hs400-enhanced-strobe;
>> - max-frequency = <384000000>;
>> - bus-width = <8>;
>> - status = "okay";
>> -};
> How is removing SDHCI related to adding support for SPI NAND flash?
> You must explain your changes in the commit message.
>


its my mistake will fix in V1

>> -
>> &tlmm {
>> - sdc_default_state: sdc-default-state {
>> - clk-pins {
>> + qspi_nand_pins: qspi_nand_pins {
> node names (between : and {) must not include underscores, use
> hyphens instead

ok

>
>> + spi_clock {
>> pins = "gpio5";
>> - function = "sdc_clk";
>> + function = "qspi_clk";
>> drive-strength = <8>;
>> bias-disable;
>> };
>>
>> - cmd-pins {
>> + qspi_cs {
>> pins = "gpio4";
>> - function = "sdc_cmd";
>> + function = "qspi_cs";
>> drive-strength = <8>;
>> bias-pull-up;
>> };
>>
>> - data-pins {
>> - pins = "gpio0", "gpio1", "gpio2",
>> - "gpio3", "gpio6", "gpio7",
>> - "gpio8", "gpio9";
>> - function = "sdc_data";
>> + qspi_data {
>> + pins = "gpio0", "gpio1", "gpio2";
>> + function = "qspi_data";
>> drive-strength = <8>;
>> bias-pull-up;
>> };
>>
>> - rclk-pins {
>> - pins = "gpio10";
>> - function = "sdc_rclk";
>> - drive-strength = <8>;
>> - bias-pull-down;
>> - };
>> + };
>> +};
>> +
>> +&qpic_bam {
>> + status = "okay";
>> +};
>> +
>> +&qpic_nand {
>> + status = "okay";
> status should come last
>> + pinctrl-0 = <&qspi_nand_pins>;
>> + pinctrl-names = "default";
>> + spi_nand: spi_nand@0 {
> no underscores in node names
> missing newline between properties and subnodes

ok

>
>> + compatible = "spi-nand";
>> + nand-ecc-engine = <&qpic_nand>;
>> + reg = <0>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + nand-ecc-strength = <4>;
>> + nand-ecc-step-size = <512>;
>> + spi-max-frequency = <8000000>;
>> };
>> };
>> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> index b44acb1fac74..f9c21373f5e6 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
>> @@ -336,10 +336,38 @@ sdhc_1: mmc@7804000 {
>> status = "disabled";
>> };
>>
>> + qpic_bam: dma@7984000 {
>> + compatible = "qcom,bam-v1.7.0";
>> + reg = <0x7984000 0x1c000>;
>> + interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&gcc GCC_QPIC_AHB_CLK>;
>> + clock-names = "bam_clk";
>> + #dma-cells = <1>;
>> + qcom,ee = <0>;
>> + status = "disabled";
>> + };
> You're modifying the SoC and board devicetrees in one go, this won't fly

Will fix in V1

>
>> +
>> + qpic_nand: spi@79b0000 {
>> + compatible = "qcom,ipq9574-nand";
>> + reg = <0x79b0000 0x10000>;
>
>> + #address-cells = <1>;
>> + #size-cells = <0>;
> these two properties usually go below status, at the end

Ok

>
>> + clocks = <&gcc GCC_QPIC_CLK>,
>> + <&gcc GCC_QPIC_AHB_CLK>,
>> + <&gcc GCC_QPIC_IO_MACRO_CLK>;
> Indentation here is messy

Will fix in V1

>
>> + clock-names = "core", "aon", "io_macro";
> one per line, please
Ok
>
>> + dmas = <&qpic_bam 0>,
>> + <&qpic_bam 1>,
>> + <&qpic_bam 2>;
> ditto
Ok
>
>> + dma-names = "tx", "rx", "cmd";
> ditto
Ok
>
>> + nand-ecc-engine = <&bch>;
>> + status = "disabled";
>> + };
>> +
>> bch: qpic_ecc {
>> compatible = "qcom,ipq9574-ecc";
>> status = "ok";
>> - }
>> + };
> This means the previous dt patch would not compile

Will fix in V1


Regards
Alam.

\
 
 \ /
  Last update: 2023-11-20 13:47    [W:0.096 / U:0.088 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site