lkml.org 
[lkml]   [2023]   [Nov]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v5 04/10] scsi: ufs: ufs-qcom: Limit negotiated gear to selected PHY gear
From


On 11/28/2023 6:52 PM, Manivannan Sadhasivam wrote:
> On Tue, Nov 28, 2023 at 04:05:59PM +0800, Can Guo wrote:
>> Hi Mani,
>>
>> On 11/28/2023 1:45 PM, Manivannan Sadhasivam wrote:
>>> On Thu, Nov 23, 2023 at 12:46:24AM -0800, Can Guo wrote:
>>>> In the dual init scenario, the initial PHY gear is set to HS-G2, and the
>>>> first Power Mode Change (PMC) is meant to find the best matching PHY gear
>>>> for the 2nd init. However, for the first PMC, if the negotiated gear (say
>>>> HS-G4) is higher than the initial PHY gear, we cannot go ahead let PMC to
>>>> the negotiated gear happen, because the programmed UFS PHY settings may not
>>>> support the negotiated gear. Fix it by overwriting the negotiated gear with
>>>> the PHY gear.
>>>>
>>>
>>> I don't quite understand this patch. If the phy_gear is G2 initially and the
>>> negotiated gear is G4, then as per this change,
>>>
>>> phy_gear = G4;
>>> negotiated gear = G2;
>>>
>>> Could you please explain how this make sense?
>>
>> phy_gear was G2 (in the beginning) and just now changed to G4, but the PHY
>> settings programmed in the beginning can only support no-G4 (not G4).
>> Without this change, as the negotiated gear is G4, the power mode change is
>> going to put UFS at HS-G4 mode, but the PHY settings programmed is no-G4.
>
> But we are going to reinit the PHY anyway, isn't it?

We are power mode changing to HS-G4 with no-G4 PHY settings programmed,
the power mode change operation, in the 1st init, may immediately cause
UIC errors and lead to probe fail. We are not seeing issues as of now,
maybe because the amount of HW used for testing is not large enough.

This change is not really related to this specific series, I can remove
it in next version.

Thanks,
Can Guo.

>
>> This change is to limit the negotiated gear to HS-G2 for the 1st init. In
>> the 2nd init, as the new PHY gear is G4, G4 PHY settings would be
>> programmed, it'd be safe to put the UFS at HS-G4 mode.
>>
>
> Why do we need to limit it since we already have the logic in place to set
> whatever gear mode applicable for 1st init?
>
> - Mani
>
>> Thanks,
>> Can Guo.
>>>
>>> - Mani
>>>
>>>> Signed-off-by: Can Guo <quic_cang@quicinc.com>
>>>> ---
>>>> drivers/ufs/host/ufs-qcom.c | 7 ++++++-
>>>> 1 file changed, 6 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
>>>> index cc0eb37..d4edf58 100644
>>>> --- a/drivers/ufs/host/ufs-qcom.c
>>>> +++ b/drivers/ufs/host/ufs-qcom.c
>>>> @@ -920,8 +920,13 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>>>> * because, the PHY gear settings are backwards compatible and we only need to
>>>> * change the PHY gear settings while scaling to higher gears.
>>>> */
>>>> - if (dev_req_params->gear_tx > host->phy_gear)
>>>> + if (dev_req_params->gear_tx > host->phy_gear) {
>>>> + u32 old_phy_gear = host->phy_gear;
>>>> +
>>>> host->phy_gear = dev_req_params->gear_tx;
>>>> + dev_req_params->gear_tx = old_phy_gear;
>>>> + dev_req_params->gear_rx = old_phy_gear;
>>>> + }
>>>> /* enable the device ref clock before changing to HS mode */
>>>> if (!ufshcd_is_hs_mode(&hba->pwr_info) &&
>>>> --
>>>> 2.7.4
>>>>
>>>
>

\
 
 \ /
  Last update: 2023-11-28 12:05    [W:0.625 / U:0.388 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site