lkml.org 
[lkml]   [2023]   [Nov]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
SubjectRe: [PATCH v5 07/10] scsi: ufs: ufs-qcom: Set initial PHY gear to max HS gear for HW ver 5 and newer
From
Hi Mani,

On 11/28/2023 2:00 PM, Manivannan Sadhasivam wrote:
> On Thu, Nov 23, 2023 at 12:46:27AM -0800, Can Guo wrote:
>> Set the initial PHY gear to max HS gear for hosts with HW ver 5 and newer.
>>
>
> MAX_GEAR will be used for hosts with hw_ver.major >= 4

I put it > 5 because I am not intent to touch any old targets which has
proven working fine with starting with PHY gear HS_G2. If I put it >= 4,
there would be many targets impacted by this change. I need to go back
and test those platforms (HW ver == 4).

Thanks,
Can Guo.

>
>> This patch is not changing any functionalities or logic but only a
>> preparation patch for the next patch in this series.
>>
>> Signed-off-by: Can Guo <quic_cang@quicinc.com>
>> ---
>> drivers/ufs/host/ufs-qcom.c | 21 +++++++++++++++------
>> 1 file changed, 15 insertions(+), 6 deletions(-)
>>
>> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
>> index 6756f8d..7bbccf4 100644
>> --- a/drivers/ufs/host/ufs-qcom.c
>> +++ b/drivers/ufs/host/ufs-qcom.c
>> @@ -1067,6 +1067,20 @@ static void ufs_qcom_advertise_quirks(struct ufs_hba *hba)
>> hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
>> }
>>
>> +static void ufs_qcom_set_phy_gear(struct ufs_qcom_host *host)
>> +{
>> + struct ufs_host_params *host_params = &host->host_params;
>> +
>> + host->phy_gear = host_params->hs_tx_gear;
>> +
>> + /*
>> + * Power up the PHY using the minimum supported gear (UFS_HS_G2).
>> + * Switching to max gear will be performed during reinit if supported.
>
> You need to reword this comment too.
>
>> + */
>> + if (host->hw_ver.major < 0x5)
>
> As I mentioned above, MAX_GEAR will be used if hw_ver.major is >=4 in
> ufs_qcom_get_hs_gear(). So this check should be (< 0x4).
>
> - Mani
>
>> + host->phy_gear = UFS_HS_G2;
>> +}
>> +
>> static void ufs_qcom_set_host_params(struct ufs_hba *hba)
>> {
>> struct ufs_qcom_host *host = ufshcd_get_variant(hba);
>> @@ -1303,6 +1317,7 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>> ufs_qcom_set_caps(hba);
>> ufs_qcom_advertise_quirks(hba);
>> ufs_qcom_set_host_params(hba);
>> + ufs_qcom_set_phy_gear(host);
>>
>> err = ufs_qcom_ice_init(host);
>> if (err)
>> @@ -1320,12 +1335,6 @@ static int ufs_qcom_init(struct ufs_hba *hba)
>> dev_warn(dev, "%s: failed to configure the testbus %d\n",
>> __func__, err);
>>
>> - /*
>> - * Power up the PHY using the minimum supported gear (UFS_HS_G2).
>> - * Switching to max gear will be performed during reinit if supported.
>> - */
>> - host->phy_gear = UFS_HS_G2;
>> -
>> return 0;
>>
>> out_variant_clear:
>> --
>> 2.7.4
>>
>

\
 
 \ /
  Last update: 2023-11-28 08:59    [W:0.202 / U:0.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site