lkml.org 
[lkml]   [2023]   [Oct]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v7 2/3] greybus: Add BeaglePlay Linux Driver
From

On 10/5/23 14:38, Greg KH wrote:
> On Thu, Oct 05, 2023 at 12:16:37AM +0530, Ayush Singh wrote:
>> Add the Greybus host driver for BeaglePlay board by BeagleBoard.org.
>>
>> The current greybus setup involves running SVC in a user-space
>> application (GBridge) and using netlink to communicate with kernel
>> space. GBridge itself uses wpanusb kernel driver, so the greybus messages
>> travel from kernel space (gb_netlink) to user-space (GBridge) and then
>> back to kernel space (wpanusb) before reaching CC1352.
>>
>> This driver directly communicates with CC1352 (running SVC Zephyr
>> application). Thus, it simplifies the complete greybus setup eliminating
>> user-space GBridge.
>>
>> This driver is responsible for the following:
>> - Start SVC (CC1352) on driver load.
>> - Send/Receive Greybus messages to/from CC1352 using HDLC over UART.
>> - Print Logs from CC1352.
>> - Stop SVC (CC1352) on driver load.
>>
>> Signed-off-by: Ayush Singh <ayushdevel1325@gmail.com>
>> ---
>> MAINTAINERS | 1 +
>> drivers/greybus/Kconfig | 10 +
>> drivers/greybus/Makefile | 2 +
>> drivers/greybus/gb-beagleplay.c | 501 ++++++++++++++++++++++++++++++++
>> 4 files changed, 514 insertions(+)
>> create mode 100644 drivers/greybus/gb-beagleplay.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 5467669d7963..d87e30626a6a 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -8974,6 +8974,7 @@ M: Ayush Singh <ayushdevel1325@gmail.com>
>> L: greybus-dev@lists.linaro.org (moderated for non-subscribers)
>> S: Maintained
>> F: Documentation/devicetree/bindings/net/ti,cc1352p7.yaml
>> +F: drivers/greybus/gb-beagleplay.c
>>
>> GREYBUS SUBSYSTEM
>> M: Johan Hovold <johan@kernel.org>
>> diff --git a/drivers/greybus/Kconfig b/drivers/greybus/Kconfig
>> index 78ba3c3083d5..fd4f26d09c53 100644
>> --- a/drivers/greybus/Kconfig
>> +++ b/drivers/greybus/Kconfig
>> @@ -17,6 +17,16 @@ menuconfig GREYBUS
>>
>> if GREYBUS
>>
>> +config GREYBUS_BEAGLEPLAY
>> + tristate "Greybus BeaglePlay driver"
>> + depends on TTY
> What you want to depend on here is serdev, not tty, right? Or am I
> mis-reading the code requirements?
>
> thanks,
>
> greg k-h

Yes, it was dependent on tty in the past, but not anymore. I think it
should be changed to `SERIAL_DEV_BUS` now?


Sincerely,

Ayush Singh

\
 
 \ /
  Last update: 2023-10-05 18:35    [W:0.097 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site