lkml.org 
[lkml]   [2023]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 1/1] drm/panel: st7703: Pick different reset sequence
On Sun, Oct 15, 2023 at 02:49:20PM +0200, Guido Günther wrote:
> Hi,
> On Sat, Feb 11, 2023 at 06:17:48PM +0100, Frank Oltmanns wrote:
> > From: Ondrej Jirman <megi@xff.cz>
> >
> > Switching to a different reset sequence, enabling IOVCC before enabling
> > VCC.
> >
> > There also needs to be a delay after enabling the supplies and before
> > deasserting the reset. The datasheet specifies 1ms after the supplies
> > reach the required voltage. Use 10-20ms to also give the power supplies
> > some time to reach the required voltage, too.
> >
> > This fixes intermittent panel initialization failures and screen
> > corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
> > used in PinePhone).
>
> Thanks, applied to drm-misc-next.
> Cheers,
> -- Guido

Thank you. Probably too late, but this fixes problems I have with a
different ST7703 based panel.

Tested-by: Chris Morgan <macromorgan@hotmail.com>

>
> >
> > Signed-off-by: Ondrej Jirman <megi@xff.cz>
> > Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
> > Reported-by: Samuel Holland <samuel@sholland.org>
> > ---
> > drivers/gpu/drm/panel/panel-sitronix-st7703.c | 25 ++++++++++---------
> > 1 file changed, 13 insertions(+), 12 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> > index 6747ca237ced..45695aa51f62 100644
> > --- a/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> > +++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> > @@ -411,29 +411,30 @@ static int st7703_prepare(struct drm_panel *panel)
> > return 0;
> >
> > dev_dbg(ctx->dev, "Resetting the panel\n");
> > - ret = regulator_enable(ctx->vcc);
> > + gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> > +
> > + ret = regulator_enable(ctx->iovcc);
> > if (ret < 0) {
> > - dev_err(ctx->dev, "Failed to enable vcc supply: %d\n", ret);
> > + dev_err(ctx->dev, "Failed to enable iovcc supply: %d\n", ret);
> > return ret;
> > }
> > - ret = regulator_enable(ctx->iovcc);
> > +
> > + ret = regulator_enable(ctx->vcc);
> > if (ret < 0) {
> > - dev_err(ctx->dev, "Failed to enable iovcc supply: %d\n", ret);
> > - goto disable_vcc;
> > + dev_err(ctx->dev, "Failed to enable vcc supply: %d\n", ret);
> > + regulator_disable(ctx->iovcc);
> > + return ret;
> > }
> >
> > - gpiod_set_value_cansleep(ctx->reset_gpio, 1);
> > - usleep_range(20, 40);
> > + /* Give power supplies time to stabilize before deasserting reset. */
> > + usleep_range(10000, 20000);
> > +
> > gpiod_set_value_cansleep(ctx->reset_gpio, 0);
> > - msleep(20);
> > + usleep_range(15000, 20000);
> >
> > ctx->prepared = true;
> >
> > return 0;
> > -
> > -disable_vcc:
> > - regulator_disable(ctx->vcc);
> > - return ret;
> > }
> >
> > static const u32 mantix_bus_formats[] = {
> > --
> > 2.39.1
> >

\
 
 \ /
  Last update: 2023-10-18 17:01    [W:5.959 / U:1.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site