Messages in this thread Patch in this message | | | Date | Tue, 17 Oct 2023 13:03:28 +0300 | From | Vladimir Oltean <> | Subject | Re: [PATCH net-next v4 1/2] net: dsa: Use conduit and user terms |
| |
On Mon, Oct 16, 2023 at 09:47:41AM -0700, Florian Fainelli wrote: > Use more inclusive terms throughout the DSA subsystem by moving away > from "master" which is replaced by "conduit" and "slave" which is > replaced by "user". No functional changes. > > Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> > ---
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Note that you left the following unconverted:
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c index d117e9b1a465..d27c6b70a2f6 100644 --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c @@ -1113,7 +1113,7 @@ mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) u32 val; /* When a new MTU is set, DSA always set the CPU port's MTU to the - * largest MTU of the slave ports. Because the switch only has a global + * largest MTU of the user ports. Because the switch only has a global * RX length register, only allowing CPU port here is enough. */ if (!dsa_is_cpu_port(ds, port)) diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c index be2491de173d..42b1acaca33a 100644 --- a/drivers/net/dsa/mv88e6xxx/chip.c +++ b/drivers/net/dsa/mv88e6xxx/chip.c @@ -2486,7 +2486,7 @@ static int mv88e6xxx_port_vlan_add(struct dsa_switch *ds, int port, else member = MV88E6XXX_G1_VTU_DATA_MEMBER_TAG_TAGGED; - /* net/dsa/slave.c will call dsa_port_vlan_add() for the affected port + /* net/dsa/user.c will call dsa_port_vlan_add() for the affected port * and then the CPU port. Do not warn for duplicates for the CPU port. */ warn = !dsa_is_cpu_port(ds, port) && !dsa_is_dsa_port(ds, port); diff --git a/drivers/net/dsa/qca/qca8k-common.c b/drivers/net/dsa/qca/qca8k-common.c index d203e4a84441..9243eff8918d 100644 --- a/drivers/net/dsa/qca/qca8k-common.c +++ b/drivers/net/dsa/qca/qca8k-common.c @@ -761,7 +761,7 @@ int qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) int ret; /* We have only have a general MTU setting. - * DSA always set the CPU port's MTU to the largest MTU of the slave + * DSA always set the CPU port's MTU to the largest MTU of the user * ports. * Setting MTU just for the CPU port is sufficient to correctly set a * value for every port. diff --git a/drivers/net/dsa/realtek/rtl8365mb.c b/drivers/net/dsa/realtek/rtl8365mb.c index d171c18dd354..0875e4fc9f57 100644 --- a/drivers/net/dsa/realtek/rtl8365mb.c +++ b/drivers/net/dsa/realtek/rtl8365mb.c @@ -1144,7 +1144,7 @@ static int rtl8365mb_port_change_mtu(struct dsa_switch *ds, int port, int frame_size; /* When a new MTU is set, DSA always sets the CPU port's MTU to the - * largest MTU of the slave ports. Because the switch only has a global + * largest MTU of the user ports. Because the switch only has a global * RX length register, only allowing CPU port here is enough. */ if (!dsa_is_cpu_port(ds, port))
| |