lkml.org 
[lkml]   [2023]   [Jan]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v1 03/11] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2
Hi Niel,


On Wed, 4 Jan 2023 at 14:26, Neil Armstrong <neil.armstrong@linaro.org> wrote:
>
> On 04/01/2023 09:13, Anand Moon wrote:
> > Hi Martin,
> >
> > On Wed, 28 Dec 2022 at 20:14, Anand Moon <linux.amoon@gmail.com> wrote:
> >>
> >> Hi Martin,
> >>
> >> On Wed, 28 Dec 2022 at 18:21, Martin Blumenstingl
> >> <martin.blumenstingl@googlemail.com> wrote:
> >>>
> >>> Hi Anand,
> >>>
> >> Thanks for your review comments.
> >>
> >>> thank you for working on this topic!
> >>>
> >>> On Wed, Dec 28, 2022 at 11:05 AM Anand Moon <linux.amoon@gmail.com> wrote:
> >>> [...]
> >>>> + usb {
> >>>> + dr_mode = "host";
> >>>> + #address-cells = <1>;
> >>>> + #size-cells = <0>;
> >>>> +
> >>>> + hub@1 {
> >>>> + /* Genesys Logic GL852G-OHG usb hub */
> >>>> + compatible = "genesys,usb5e3,610";
> >>>> + reg = <1>;
> >>>> + vdd-supply = <&usb_otg_pwr>;
> >>>> + reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
> >>>> + };
> >>>> + };
> >>> My understanding is that the hub@1 node should be part of the
> >>> corresponding USB controller node, not a new node.
> >>> In this case hub@1 should go into the existing &usb1 node. That way we
> >>> describe the way the hardware is set up (meaning: hub@1 is connected
> >>> to &usb1).
> >>>
> >>
> >> Ok, I will move this code under &usb0 and &usb1 nodes.
> >>
> >> onboard_usb_hub module just assists in usb hub reset.
> >> so these changes are meant to replace the gpio-hog.
> >>
> >> $ dmesg | grep onboard
> >> [ 5.405558] usbcore: registered new device driver onboard-usb-hub
> >> [ 6.383428] onboard-usb-hub 1-1: reset high-speed USB device number
> >> 2 using dwc2
> >>
> >> Here is the boot log of the odroid c2 [0] https://pastebin.com/PFy5waPb
> >>
> >
> > Moving the usb hub into usb subnode usb0 or usb1 does not work
> > on Odroid n2 and c4, we have a combo phys of usb 2.0 and usb 3.0
> > so the onboard usb hub reset does not get initialized until both the PHY
> > and USB nodes are brought up by the drivers.
>
> Fine, then add a comment before the usb node explaining that.
>

Sure, thanks.

> Thanks,
> Neil
>
Thanks
-Anand

\
 
 \ /
  Last update: 2023-03-26 23:26    [W:0.059 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site