lkml.org 
[lkml]   [2023]   [Jan]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/4] media: i2c: ov2685: Make reset gpio optional
Hi Luca

On Sun, Jan 29, 2023 at 12:49:03PM +0100, Luca Weiss wrote:
> On Sonntag, 29. Jänner 2023 12:22:49 CET Jacopo Mondi wrote:
> > Hi Luca
> >
> > On Sun, Jan 29, 2023 at 10:42:35AM +0100, Luca Weiss wrote:
> > > In some setups XSHUTDOWN is connected to DOVDD when it's unused,
> > > therefore treat the reset gpio as optional.
> >
> > I don't have a datasheet for this sensor, but OV sensors usually have
> > to gpio lines to control powerdown and reset. Datasheets usually
> > suggest to hook one of the 2 to DOVDD and control the other from the
> > SoC. How is the sensor hooked up in your design ? No gpio lines is
> > controlled by the SoC ?
>
> It looks like this sensor only has XSHUTDOWN pin and no extra reset pin.
>

Ack, I see the same for OV2680 (for which I have a datasheet)

> In my setup there's the normal I2C & CSI & mclk hookups, but the supply lines
> and shutdown line are all just connected to regulator-fixed, so gpio-
> controlled on/off regulators.
>
> >
> > Another question is if we need to software-reset the sensor if no gpio
> > line is hooked up to XSHUTDOWN.
>
> The datasheet mentions it resets itself during power up (so when the supplies
> are turned on), so I don't think we need to add anything.
>

Thanks for the clarification!

Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>

Thanks
j


> Regards
> Luca
>
> >
> > > Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> > > ---
> > >
> > > drivers/media/i2c/ov2685.c | 2 +-
> > > 1 file changed, 1 insertion(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/media/i2c/ov2685.c b/drivers/media/i2c/ov2685.c
> > > index a3b524f15d89..a422f4c8a2eb 100644
> > > --- a/drivers/media/i2c/ov2685.c
> > > +++ b/drivers/media/i2c/ov2685.c
> > > @@ -734,7 +734,7 @@ static int ov2685_probe(struct i2c_client *client,
> > >
> > > if (clk_get_rate(ov2685->xvclk) != OV2685_XVCLK_FREQ)
> > >
> > > dev_warn(dev, "xvclk mismatched, modes are based on
> 24MHz\n");
> > >
> > > - ov2685->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> > > + ov2685->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> > > GPIOD_OUT_LOW);>
> > > if (IS_ERR(ov2685->reset_gpio)) {
> > >
> > > dev_err(dev, "Failed to get reset-gpios\n");
> > > return -EINVAL;
> > >
> > > --
> > > 2.39.1
>
>
>
>

\
 
 \ /
  Last update: 2023-03-27 00:01    [W:0.118 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site