lkml.org 
[lkml]   [2023]   [Jan]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Date
    Subject[PATCH 3/5] ARM: dts: qcom: msm8974-oneplus-bacon: Add volume keys and hall sensor
    Add nodes for the volume buttons and the hall sensor that are found on
    the device.

    Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
    ---
    .../arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts | 50 ++++++++++++++++++++++
    1 file changed, 50 insertions(+)

    diff --git a/arch/arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts b/arch/arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts
    index 63180fe1d292..10ba3c94e26d 100644
    --- a/arch/arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts
    +++ b/arch/arm/boot/dts/qcom-msm8974pro-oneplus-bacon.dts
    @@ -19,6 +19,38 @@ aliases {
    chosen {
    stdout-path = "serial0:115200n8";
    };
    +
    + gpio-keys {
    + compatible = "gpio-keys";
    +
    + pinctrl-names = "default";
    + pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
    +
    + key-volume-down {
    + label = "Volume Down";
    + gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
    + linux,code = <KEY_VOLUMEDOWN>;
    + wakeup-source;
    + debounce-interval = <15>;
    + };
    +
    + key-volume-up {
    + label = "Volume Up";
    + gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
    + linux,code = <KEY_VOLUMEUP>;
    + wakeup-source;
    + debounce-interval = <15>;
    + };
    +
    + event-hall-sensor {
    + label = "Hall Effect Sensor";
    + gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
    + linux,input-type = <EV_SW>;
    + linux,code = <SW_LID>;
    + linux,can-disable;
    + debounce-interval = <150>;
    + };
    + };
    };

    &blsp1_i2c1 {
    @@ -95,6 +127,17 @@ &pm8941_coincell {
    status = "okay";
    };

    +&pm8941_gpios {
    + gpio_keys_default: gpio-keys-active-state {
    + pins = "gpio2", "gpio5";
    + function = "normal";
    +
    + input-enable;
    + bias-disable;
    + power-source = <PM8941_GPIO_S3>;
    + };
    +};
    +
    &pm8941_vib {
    status = "okay";
    };
    @@ -349,6 +392,13 @@ &sdhc_1 {
    };

    &tlmm {
    + gpio_hall_sensor_default: gpio-hall-sensor-default-state {
    + pins = "gpio68";
    + function = "gpio";
    + drive-strength = <8>;
    + bias-pull-up;
    + };
    +
    sdc1_on: sdc1-on-state {
    clk-pins {
    pins = "sdc1_clk";
    --
    2.39.1

    \
     
     \ /
      Last update: 2023-03-26 23:51    [W:2.392 / U:0.036 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site