lkml.org 
[lkml]   [2023]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [RFC v4 5/5] arm: dts: msm: Add multiport controller node for usb
From


On 1/18/2023 11:58 PM, Bjorn Andersson wrote:
> On Sun, Jan 15, 2023 at 05:11:46PM +0530, Krishna Kurapati wrote:
>> Add USB and DWC3 node for teritiary port of SC8280 along
>> with multiport IRQ's and phy's.
>>
>
> Very nice.
>
> Please make the subject prefix "arm64: dts: qcom: sc8280xp:", to match
> other changes in the sc8280xp.dtsi.
>> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 49 +++++++++++++++++++
>> arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 60 ++++++++++++++++++++++++
>> 2 files changed, 109 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
>> index 84cb6f3eeb56..f9eb854c3444 100644
>> --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
>> +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
>> @@ -422,6 +422,20 @@ &usb_1_qmpphy {
>> status = "okay";
>> };
>>
>> +&usb_2 {
>> + status = "okay";
>
> Please the status property last in the node.
>
>> +
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&usb2_en_state>,
>> + <&usb3_en_state>,
>> + <&usb4_en_state>,
>> + <&usb5_en_state>;
>> +};
>> +
>> +&usb_2_dwc3 {
>> + dr_mode = "host";
>> +};
>> +
>> &usb_2_hsphy0 {
>> vdda-pll-supply = <&vreg_l5a>;
>> vdda18-supply = <&vreg_l7g>;
>> @@ -472,6 +486,41 @@ &xo_board_clk {
>> clock-frequency = <38400000>;
>> };
>>
>> +/* PINCTRL */
>
> No need to repeat this comment, its purpose is to indicate that nodes
> above are sorted alphabetically and pinctrl-related nodes are kept here
> at the end of the file. Please place your nodes below the existing /*
> PINCTRL */ comment below.
>
> Thanks,
> Bjorn
>
>> +&pm8450c_gpios {
>> + usb2_en_state: usb2-en-state {
>> + pins = "gpio9";
>> + function = "normal";
>> + output-high;
>> + power-source = <0>;
>> + };
>> +};
>> +
>> +&pm8450e_gpios {
>> + usb3_en_state: usb3-en-state {
>> + pins = "gpio5";
>> + function = "normal";
>> + output-high;
>> + power-source = <0>;
>> + };
>> +};
>> +
>> +&pm8450g_gpios {
>> + usb4_en_state: usb4-en-state {
>> + pins = "gpio5";
>> + function = "normal";
>> + output-high;
>> + power-source = <0>;
>> + };
>> +
>> + usb5_en_state: usb5-en-state {
>> + pins = "gpio9";
>> + function = "normal";
>> + output-high;
>> + power-source = <0>;
>> + };
>> +};
>> +
>> /* PINCTRL */
>>
>> &tlmm {
>> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
>> index 109c9d2b684d..e9866ab5c6e2 100644
>> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
>> @@ -1969,6 +1969,66 @@ usb_1_dwc3: usb@a800000 {
>> };
>> };
>>
>> + usb_2: usb@a4f8800 {
>> + compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
>> + reg = <0 0x0a4f8800 0 0x400>;
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> + ranges;
>> +
>> + clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
>> + <&gcc GCC_USB30_MP_MASTER_CLK>,
>> + <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
>> + <&gcc GCC_USB30_MP_SLEEP_CLK>,
>> + <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
>> + <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
>> + <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
>> + <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
>> + <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
>> + clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
>> + "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
>> +
>> + assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
>> + <&gcc GCC_USB30_MP_MASTER_CLK>;
>> + assigned-clock-rates = <19200000>, <200000000>;
>> +
>> + interrupts-extended = <&pdc 127 IRQ_TYPE_EDGE_RISING>,
>> + <&pdc 126 IRQ_TYPE_EDGE_RISING>,
>> + <&pdc 16 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + interrupt-names = "dp_hs_phy_irq", "dm_hs_phy_irq",
>> + "ss_phy_irq";
>> +
>> + power-domains = <&gcc USB30_MP_GDSC>;
>> +
>> + resets = <&gcc GCC_USB30_MP_BCR>;
>> +
>> + interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
>> + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
>> + interconnect-names = "usb-ddr", "apps-usb";
>> +
>> + required-opps = <&rpmhpd_opp_nom>;
>> +
>> + status = "disabled";
>> +
>> + usb_2_dwc3: usb@a400000 {
>> + compatible = "snps,dwc3";
>> + reg = <0 0x0a400000 0 0xcd00>;
>> + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
>> + iommus = <&apps_smmu 0x800 0x0>;
>> + num-ports = <4>;
>> + num-ss-ports = <2>;
>> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>,
>> + <&usb_2_hsphy1>, <&usb_2_qmpphy1>,
>> + <&usb_2_hsphy2>,
>> + <&usb_2_hsphy3>;
>> + phy-names = "usb2-phy_port0", "usb3-phy_port0",
>> + "usb2-phy_port1", "usb3-phy_port1",
>> + "usb2-phy_port2",
>> + "usb2-phy_port3";
>> + };
>> + };
>> +
>> pdc: interrupt-controller@b220000 {
>> compatible = "qcom,sc8280xp-pdc", "qcom,pdc";
>> reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
>> --
>> 2.39.0
>>

Hi Bjorn,

Thanks for the review. Will make sure to incorporate these changes in
the next version.

Regards,
Krishna,

\
 
 \ /
  Last update: 2023-03-26 23:46    [W:0.121 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site