lkml.org 
[lkml]   [2023]   [Jan]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v3 0/7] perf cs_etm: Basic support for virtual/kernel timestamps
From


On 12/01/2023 15:33, Tanmay Jagdale wrote:
> Hi James
>
>>>>> base-commit: 09e6f9f98370be9a9f8978139e0eb1be87d1125f
>>>> I have tested this patch set on our platform and able to see updated
>>>> timestamp values in perf script's output.
>>>>
>>>> $ perf record -e cs_etm/cycacc,@tmc_etr0/k -C 9 taskset -c 9 sleep 2
>>>> $ perf script --itrace=i1ns --ns -Fcomm,tid,pid,time,cpu,event,ip,sym,addr,symoff,flags,callindent
>>>>
>>>> At certain points noticed that hardware emits same timestamp packets
>>>> but with updated cycle count (CC) values. A small snippet of the log:
>>>>
>>>> Idx:100; ID:12; I_ADDR_S_IS0 : Address, Short, IS0.; Addr=0xFFFF8000086A761C ~[0x761C]
>>>> Idx:103; ID:12; I_TIMESTAMP : Timestamp.; Updated val = 0x2f373e37e02; CC=0x3d
>>>> Idx:107; ID:12; I_ATOM_F2 : Atom format 2.; EN
>>>> Idx:108; ID:12; I_TIMESTAMP : Timestamp.; Updated val = 0x2f373e37e02; CC=0x3f
>>>> Idx:112; ID:12; I_ATOM_F1 : Atom format 1.; N
>>>> Idx:113; ID:12; I_TIMESTAMP : Timestamp.; Updated val = 0x2f373e37e02; CC=0x45
>>>> Idx:116; ID:12; I_ATOM_F1 : Atom format 1.; E
>>>> Idx:117; ID:12; I_ADDR_S_IS0 : Address, Short, IS0.; Addr=0xFFFF8000086B52D4 ~[0x152D4]
>>>>
>>>> Since the source of timestamp is the Generic Timer block and the CPUs
>>>> run at higher frequencies, this behaviour could be possible on high
>>>> performance ARM cores.
>>>>
>>>> Having consecutive timestamps with same value is resulting in a
>>>> slightly jumbled order (in nanosecs) in perf script's time column.
>>>> A snippet corresponding to the Coresight trace data mentioned above:
>>>> ...
>>>> perf 965/965 [001] 3182.286629044: instructions:k: return 0 ffff8000086a761c coresight_timeout+0xc8
>>>> perf 965/965 [001] 3182.286629044: instructions:k: return 0 ffff8000086a7620 coresight_timeout+0xcc
>>>> perf 965/965 [001] 3182.286629046: instructions:k: jmp 0 ffff8000086a75c8 coresight_timeout+0x74
>>>> perf 965/965 [001] 3182.286629046: instructions:k: jmp 0 ffff8000086a75cc coresight_timeout+0x78
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75d0 coresight_timeout+0x7c
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75d4 coresight_timeout+0x80
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75d8 coresight_timeout+0x84
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75dc coresight_timeout+0x88
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75e0 coresight_timeout+0x8c
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75e4 coresight_timeout+0x90
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75e8 coresight_timeout+0x94
>>>> perf 965/965 [001] 3182.286629044: instructions:k: jcc 0 ffff8000086a75ec coresight_timeout+0x98
>>>>
>>>> Perf's do_soft_timestamp() logic in cs_etm_decoder.c file is incrementing
>>>> the HW timestamp based on instruction count. Since the next timestamp
>>>> also has the same value, it could be leading to this jumbled order.
>>>>
>>>> We would like to know if this has been observed on other platforms ?
>>>> And what could be a solution in SW for this ?
>>>
>>> Nice catch. If I'm understanding this correctly it looks like the issue
>>> is a combination of the cycle count in the packet being ignored by Perf,
>>> and the instruction count being reset to 0 when a new timestamp is received.
>>>
>>> It looks like it can be fixed by some combination of combining the cycle
>>> count and instruction count and maybe not resetting instruction count if
>>> the newly received timestamp is the same as the last one. I will look
>>> into this.
>>>
>>> We haven't noticed it on any other platforms, but we haven't been
>>> looking too closely at the timestamps until now. Perhaps I can add a
>>> test that checks if the trace in a known function goes in the correct
>>> time order.
>>>
>>
>> I'm thinking of something like the following patch to fix the ordering.
>> It doesn't use the cycle count, but I'm not sure if that would be
>> worthwhile in the end, considering that it would have sub nanosecond
>> resolution so wouldn't affect the Perf timestamps:
> Thanks for coming up with a quick solution for this issue !
>
>>
>>
>> diff --git a/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c b/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c
>> index 31fa3b45134a..08a028e3e87a 100644
>> --- a/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c
>> +++ b/tools/perf/util/cs-etm-decoder/cs-etm-decoder.c
>> @@ -112,6 +112,19 @@ int cs_etm_decoder__get_packet(struct cs_etm_packet_queue *packet_queue,
>> return 1;
>> }
>>
>> +static u64 cs_etm_decoder__instr_count_to_ns(u64 instr_count)
>> +{
>> + /*
>> + * Assume a maximum of 0.1ns elapsed per instruction. This would be the
>> + * case with a theoretical 10GHz core executing 1 instruction per cycle.
>> + * Used to estimate the sample time for synthesized instructions because
>> + * Coresight only emits a timestamp for a range of instructions rather
>> + * than per instruction.
>> + */
>> + const int INSTR_PER_NS = 10;
>> +
>> + return instr_count / INSTR_PER_NS;
>> +}
>> static int cs_etm_decoder__gen_etmv3_config(struct cs_etm_trace_params *params,
>> ocsd_etmv3_cfg *config)
>> {
>> @@ -267,7 +280,7 @@ cs_etm_decoder__do_soft_timestamp(struct cs_etm_queue *etmq,
>> packet_queue->cs_timestamp = packet_queue->next_cs_timestamp;
>>
>> /* Estimate the timestamp for the next range packet */
>> - packet_queue->next_cs_timestamp += packet_queue->instr_count;
>> + packet_queue->next_cs_timestamp += cs_etm_decoder__instr_count_to_ns(packet_queue->instr_count);
>> packet_queue->instr_count = 0;
>>
>> /* Tell the front end which traceid_queue needs attention */
>> @@ -295,11 +308,17 @@ cs_etm_decoder__do_hard_timestamp(struct cs_etm_queue *etmq,
>> * hence asking the decoder to keep decoding rather than stopping.
>> */
>> if (packet_queue->cs_timestamp) {
>> - packet_queue->next_cs_timestamp = elem->timestamp;
>> + /*
>> + * Don't allow next_cs_timestamp to be less than the last one estimated by
>> + * cs_etm_decoder__do_soft_timestamp() otherwise new instructions would
>> + * appear to go back in time. In theory this should never happen, but if
>> + * it did, then next_cs_timestamp should eventually catch up to real time
>> + * unless every single range was predicted to be too long for some reason.
>> + */
>> + packet_queue->next_cs_timestamp = max(elem->timestamp, packet_queue->next_cs_timestamp);
>> return OCSD_RESP_CONT;
>> }
>>
>> -
>> if (!elem->timestamp) {
>> /*
>> * Zero timestamps can be seen due to misconfiguration or hardware bugs.
>> @@ -312,7 +331,7 @@ cs_etm_decoder__do_hard_timestamp(struct cs_etm_queue *etmq,
>> ". Decoding may be improved by prepending 'Z' to your current --itrace
>> arguments.\n",
>> indx);
>>
>> - } else if (packet_queue->instr_count > elem->timestamp) {
>> + } else if (cs_etm_decoder__instr_count_to_ns(packet_queue->instr_count) > elem->timestamp) {
>> /*
>> * Sanity check that the elem->timestamp - packet_queue->instr_count would not
>> * result in an underflow. Warn and clamp at 0 if it would.
>> @@ -327,7 +346,8 @@ cs_etm_decoder__do_hard_timestamp(struct cs_etm_queue *etmq,
>> * which instructions started by subtracting the number of instructions
>> * executed to the timestamp.
>> */
>> - packet_queue->cs_timestamp = elem->timestamp - packet_queue->instr_count;
>> + packet_queue->cs_timestamp = elem->timestamp -
>> + cs_etm_decoder__instr_count_to_ns(packet_queue->instr_count);
>> }
>> packet_queue->next_cs_timestamp = elem->timestamp;
>> packet_queue->instr_count = 0;
> I have tested this diff along with the patchset and found that
> timestamps are generated/estimated in an increasing order.
>
> However, found few corner cases where they weren't in order.
> I'm currently gathering more information on these corner cases.
>
> Used the following steps to find inconsistencies:
> $ perf record -e cs_etm/@tmc_etr0/k -C 4 taskset -c 4 sleep 1
> $ perf script --itrace=i1ns --ns -Fcomm,tid,pid,time,cpu,event,ip,sym,addr,symoff,flags,callindent > itrace
> $ sed 's/://g' itrace | awk -F '.' ' { print $2 } ' | awk '{ if ($1 < prev) { print "line:" NR " " $0 } {prev=$1}}'
>
> Setting INSTR_PER_NS to higher values (14,16,20 etc) results in
> lower inconsistencies but it would defeat the purpose of
> estimating values in software since we could be returning 0
> from __instr_count_to_ns() in many cases.
>
> Please share your thoughts.

I believe this could be because I was adding nanosecond values
to the raw coresight counter before it was converted which was
a mistake. I have made another change to move the conversion
as early as possible to avoid mistakes like this.

Increasing the INSTR_PER_NS shouldn't be required because of
the max() call, in fact INSTR_PER_NS isn't necessarily
needed at all, I just thought it would make it more accurate.

I'll test the new version on the file that you sent before
pasting it here. If you have another recording that has more
of the edge cases then please also upload that one too.

James

\
 
 \ /
  Last update: 2023-03-26 23:39    [W:0.070 / U:1.448 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site