lkml.org 
[lkml]   [2023]   [Jan]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [PATCH v5 6/6] arm64: dts: qcom: sm6125: Initial support for xiaomi-laurel-sprout
From
On 31/12/2022 23:24, Lux Aliaga wrote:
> Adds support for the Xiaomi Mi A3 (xiaomi-laurel-sprout). Here's a
> summary on what's working.
>
> - dmesg output to bootloader preconfigured display
> - USB
> - UFS
> - SD card


(...)

> + };
> +
> + extcon_usb: usb-id {
> + compatible = "linux,extcon-usb-gpio";
> + id-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
> + };
> +
> + gpio-keys {
> + status = "okay";

Drop.

> + compatible = "gpio-keys";
> + autorepeat;
> +
> + key-vol-up {
> + label = "Volume Up";
> + gpios = <&pm6125_gpio 5 GPIO_ACTIVE_LOW>;
> + linux,input-type = <1>;
> + linux,code = <KEY_VOLUMEUP>;
> + gpio-key,wakeup;
> + debounce-interval = <15>;
> + };
> + };
> +
> + thermal-zones {
> + rf-pa0-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&pm6125_adc_tm 0>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + quiet-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <5000>;
> + thermal-sensors = <&pm6125_adc_tm 1>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + xo-thermal {
> + polling-delay-passive = <0>;
> + polling-delay = <0>;
> + thermal-sensors = <&pm6125_adc_tm 2>;
> +
> + trips {
> + active-config0 {
> + temperature = <125000>;
> + hysteresis = <1000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +};
> +
> +&hsusb_phy1 {
> + vdd-supply = <&vreg_l7a>;
> + vdda-pll-supply = <&vreg_l10a>;
> + vdda-phy-dpdm-supply = <&vreg_l15a>;
> + status = "okay";
> +};
> +
> +&pm6125_adc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&camera_flash_therm &emmc_ufs_therm>;
> +
> + rf-pa0-therm@4d {
> + reg = <ADC5_AMUX_THM1_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + };
> +
> + quiet-therm@4e {
> + reg = <ADC5_AMUX_THM2_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + };
> +
> + camera-flash-therm@52 {
> + reg = <ADC5_GPIO1_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + };
> +
> + emmc-ufs-therm@54 {
> + reg = <ADC5_GPIO3_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time = <200>;
> + qcom,pre-scaling = <1 1>;
> + };
> +};
> +
> +&pm6125_adc_tm {
> + status = "okay";
> +
> + rf-pa0-therm@0 {
> + reg = <0>;
> + io-channels = <&pm6125_adc ADC5_AMUX_THM1_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +
> + quiet-therm@1 {
> + reg = <1>;
> + io-channels = <&pm6125_adc ADC5_AMUX_THM2_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +
> + xo-therm@2 {
> + reg = <2>;
> + io-channels = <&pm6125_adc ADC5_XO_THERM_100K_PU>;
> + qcom,ratiometric;
> + qcom,hw-settle-time-us = <200>;
> + };
> +};
> +
> +&pm6125_gpio {
> + camera_flash_therm: camera-flash-therm-state {
> + pins = "gpio3";
> + function = PMIC_GPIO_FUNC_NORMAL;
> + bias-high-impedance;
> + };
> +
> + emmc_ufs_therm: emmc-ufs-therm-state {
> + pins = "gpio6";
> + function = PMIC_GPIO_FUNC_NORMAL;
> + bias-high-impedance;
> + };
> +
> + key_vol_up: key_vol_up {


No underscores in node names, missing state suffix.

> + pins = "gpio5";
> + function = PMIC_GPIO_FUNC_NORMAL;
> + input-enable;
> + bias-pull-up;
> + };
> +};
> +

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2023-03-26 23:24    [W:2.162 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site