lkml.org 
[lkml]   [2022]   [Sep]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 5.19 057/155] tty: serial: atmel: Preserve previous USART mode if RS485 disabled
Date
From: Sergiu Moga <sergiu.moga@microchip.com>

commit 692a8ebcfc24f4a5bea0eb2967e450f584193da6 upstream.

Whenever the atmel_rs485_config() driver method would be called,
the USART mode is reset to normal mode before even checking if
RS485 flag is set, thus resulting in losing the previous USART
mode in the case where the checking fails.

Some tools, such as `linux-serial-test`, lead to the driver calling
this method when doing the setup of the serial port: after setting the
port mode (Hardware Flow Control, Normal Mode, RS485 Mode, etc.),
`linux-serial-test` tries to enable/disable RS485 depending on
the commandline arguments that were passed.

Example of how this issue could reveal itself:
When doing a serial communication with Hardware Flow Control through
`linux-serial-test`, the tool would lead to the driver roughly doing
the following:
- set the corresponding bit to 1 (ATMEL_US_USMODE_HWHS bit in the
ATMEL_US_MR register) through the atmel_set_termios() to enable
Hardware Flow Control
- disable RS485 through the atmel_config_rs485() method
Thus, when the latter is called, the mode will be reset and the
previously set bit is unset, leaving USART in normal mode instead of
the expected Hardware Flow Control mode.

This fix ensures that this reset is only done if the checking for
RS485 succeeds and that the previous mode is preserved otherwise.

Fixes: e8faff7330a35 ("ARM: 6092/1: atmel_serial: support for RS485 communications")
Cc: stable <stable@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Link: https://lore.kernel.org/r/20220824142902.502596-1-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/tty/serial/atmel_serial.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)

--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -296,9 +296,6 @@ static int atmel_config_rs485(struct uar

mode = atmel_uart_readl(port, ATMEL_US_MR);

- /* Resetting serial mode to RS232 (0x0) */
- mode &= ~ATMEL_US_USMODE;
-
if (rs485conf->flags & SER_RS485_ENABLED) {
dev_dbg(port->dev, "Setting UART to RS485\n");
if (rs485conf->flags & SER_RS485_RX_DURING_TX)
@@ -308,6 +305,7 @@ static int atmel_config_rs485(struct uar

atmel_uart_writel(port, ATMEL_US_TTGR,
rs485conf->delay_rts_after_send);
+ mode &= ~ATMEL_US_USMODE;
mode |= ATMEL_US_USMODE_RS485;
} else {
dev_dbg(port->dev, "Setting UART to RS232\n");

\
 
 \ /
  Last update: 2022-09-06 16:06    [W:0.488 / U:0.400 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site