lkml.org 
[lkml]   [2022]   [Sep]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v10 3/4] pwm: add microchip soft ip corePWM driver
On Fri, Sep 30, 2022 at 11:13:16AM +0200, Uwe Kleine-König wrote:
> On Mon, Sep 19, 2022 at 03:29:19PM +0100, Conor Dooley wrote:
> > Hey Uwe,
> >
> > On Mon, Sep 19, 2022 at 03:50:08PM +0200, Uwe Kleine-König wrote:
> > > On Mon, Sep 19, 2022 at 01:53:56PM +0100, Conor Dooley wrote:
> > > > Because I was running into conflicts between the reporting here and some
> > > > of the checks that I have added to prevent the PWM being put into an
> > > > invalid state. On boot both negedge and posedge will be zero & this was
> > > > preventing me from setting the period at all.
> > >
> > > I don't understood that.
> >
> > On startup, (negedge == posedge) is true as both are zero, but the reset
> > values for prescale and period are actually 0x8. If on reset I try to
> > set a small period, say "echo 1000 > period" apply() returns -EINVAL
> > because of a check in the pwm core in pwm_apply_state() as I am
> > attempting to set the period to lower than the out-of-reset duty cycle.
>
> You're supposed to keep the period for pwm#1 untouched while configuring
> pwm#0 only if pwm#1 already has a consumer. So if pwm#1 isn't requested,
> you can change the period for pwm#0.

I must have done a bad job of explaining here, as I don't think this is
an answer to my question.

On reset, the prescale and period_steps registers are set to 0x8. If I
attempt to set the period to do "echo 1000 > period", I get -EINVAL back
from pwm_apply_state() (in next-20220928 it's @ L562 in pwm/core.c) as
the duty cycle is computed as twice the period as, on reset, we have
posedge = negedge = 0x0. The check of state->duty_cycle > state->period
fails in pwm_apply_state() as a result.

This failure to assign a value is unrelated to having multiple PWMs, I
think I may have horribly worded my statement when I originally replied
to you with:
> Because I was running into conflicts between the reporting here and some
> of the checks that I have added to prevent the PWM being put into an
> invalid state.

"reporting here" from that quote being the period/duty cycle
calculations in the drivers get_state(). By "the checks" I meant making
sure that a period where posedge = negedge is not set by the driver. I
think I also may have mistakenly assumed the -EINVAL came from my code
and not from the core - but I cannot be sure as it has been a few weeks.

The check in the core looks to be things "working as intended", and it
looks like I am working around it here. Should I just note what the
values are on reset in the "limitations" comment and the top & it is up
to applications that control the PWMs to first "fix" the duty cycle
before changing the period?

Hopefully I've done a better job at explaning this time,
Conor.


\
 
 \ /
  Last update: 2022-09-30 11:47    [W:0.083 / U:26.132 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site