lkml.org 
[lkml]   [2022]   [Sep]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 2/2] dt-bindings: add bindings for QCOM flash LED
On Thu, Sep 29, 2022 at 02:40:05PM +0200, Krzysztof Kozlowski wrote:
> On 29/09/2022 14:15, Fenglin Wu wrote:
> > Add binding document for flash LED module inside Qualcomm Technologies,
> > Inc. PMICs.
> >
> > Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
>
> Thank you for your patch. There is something to discuss/improve.
>
> > + reg:
> > + description: address offset of the flash LED controller
> > + maxItems: 1
> > +
> > +patternProperties:
> > + "^led[0-3]$":
>
> In such case: ^led-[0-9]$"
>
> > + type: object
> > + $ref: common.yaml#
> > + unevaluatedProperties: false
> > + description: |
> > + Represents the physical LED components which are connected to the
> > + flash LED channels' output.
> > +
> > + properties:
> > + led-sources:

This is for when the power source and LED connection are programmable.
IOW, when 'reg' is not enough to describe the configuration. If you only
have LED channels 1-4 with a fixed connection to LED pins/output 1-4,
then use 'reg'.

> > + description: |
> > + The HW indices of the flash LED channels that connect to the
> > + physical LED
> > + allOf:
> > + - minItems: 1
> > + maxItems: 2
> > + items:
> > + enum: [1, 2, 3, 4]
> > +
> > + led-max-microamp:
> > + description: |
> > + The maximum current value when LED is not operating in flash mode (i.e. torch mode)
> > + Valid values when an LED is connected to one flash LED channel:
> > + 5000 - 500000, step by 5000
> > + Valid values when an LED is connected to two flash LED channels:
> > + 10000 - 1000000, step by 10000
> > + minimum: 5000
> > + maximum: 1000000

anyOf:
- minimum: 5000
maximum: 500000
multipleOf: 5000
- minimum: 10000
maximum: 1000000
multipleOf: 10000

Drop any description that's captured by the constraints.

> > +
> > + flash-max-microamp:
> > + description: |
> > + The maximum current value when LED is operating in flash mode.
> > + Valid values when an LED is connected to one flash LED channel:
> > + 12500 - 1500000, step by 12500
> > + Valid values when an LED is connected to two flash LED channels:
> > + 25000 - 2000000, step by 12500
> > + minimum: 12500
> > + maximum: 2000000
> > +
> > + flash-max-timeout-us:
> > + description: |
> > + The maximum timeout value when LED is operating in flash mode.
> > + Valid values: 10000 - 1280000, step by 10000
> > + minimum: 10000
> > + maximum: 1280000

Similar comment for these 2.

> > +
> > + required:
> > + - led-sources
> > + - led-max-microamp
> > +
> > +required:
> > + - compatible
> > + - reg
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/leds/common.h>
> > + spmi_bus {
>
> No underscores in node names, so just "bus"

SPMI is something else though...

\
 
 \ /
  Last update: 2022-09-30 21:35    [W:0.052 / U:0.380 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site