lkml.org 
[lkml]   [2022]   [Sep]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 05/28] KVM: x86: Don't inhibit APICv/AVIC if xAPIC ID mismatch is due to 32-bit ID
From
Date
On Wed, 2022-09-28 at 18:03 +0000, Sean Christopherson wrote:
> On Wed, Sep 28, 2022, Maxim Levitsky wrote:
> > On Wed, 2022-09-28 at 16:51 +0000, Sean Christopherson wrote:
> > > > > It happens regardless of vCPU count (tested with 2, 32, 255, 380, and
> > > > > 512 vCPUs). This state persists for all subsequent reboots, until the VM
> > > > > is terminated. For vCPU counts < 256, when x2apic is disabled the
> > > > > problem does not occur, and AVIC continues to work properly after reboots.
> > >
> > > Bit of a shot in the dark, but does the below fix the issue? There are two
> > > issues with calling kvm_lapic_xapic_id_updated() from kvm_apic_state_fixup():
> > >
> > > 1. The xAPIC ID should only be refreshed on "set".
> > True - I didn't bother to fix it yet because it shouldn't cause harm, but
> > sure this needs to be fixed.
>
> It's probably benign on its own, but with the missing "hardware enabled" check,
> it could be problematic if userspace does KVM_GET_LAPIC while the APIC is hardware
> disabled, after the APIC was previously in x2APIC mode. I'm guessing QEMU does
> KVM_GET_LAPIC state when emulating reboot, hence the potential for being involved
> in the bug Alejandro is seeing.
>
> > > 2. The refresh needs to be noted after memcpy(vcpu->arch.apic->regs, s->regs, sizeof(*s));
> > Are you sure? The check is first because if it fails, then error is returned to userspace
> > and the KVM's state left unchanged.
> >
> > I assume you are talking about
> >
> > ....
> > r = kvm_apic_state_fixup(vcpu, s, true);
> > if (r) {
> > kvm_recalculate_apic_map(vcpu->kvm);
> > return r;
> > }
> > memcpy(vcpu->arch.apic->regs, s->regs, sizeof(*s));
>
> This isn't a failure path though, it's purely a "take note of the update", and
> KVM needs to do that processing _after_ the actual update. Specifically,
> kvm_lapic_xapic_id_updated() consumes the internal APIC state:

Yes, I somehow blindly assumed that kvm_apic_state_fixup actually checks
the new state and not the existing state.

Probably because my original code did that, I think it just checked the 'id'
variable.. Oh well.
Thanks for catching this bug!

Best regards,
Maxim Levitsky

>
> if (kvm_xapic_id(apic) == apic->vcpu->vcpu_id)
> return;
>
> Calling that before the internal state has been set with the incoming state from
> userspace is simply wrong.
>
> The check that the x2APIC ID is "correct" stays where it is, this is purely the
> "is the xAPIC ID different" path.
>


\
 
 \ /
  Last update: 2022-09-28 20:18    [W:0.103 / U:0.612 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site