lkml.org 
[lkml]   [2022]   [Sep]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 5.4 032/120] usb: dwc3: gadget: Refactor pullup()
Date
From: Thinh Nguyen <Thinh.Nguyen@synopsys.com>

[ Upstream commit 861c010a2ee1bc4a66d23f0da4aa22e75d8eaa24 ]

Move soft-disconnect sequence out of dwc3_gadget_pullup(). No
functional change here.

Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/4c0f259b17d95acaaa931f90276683a48a32fe22.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/usb/dwc3/gadget.c | 65 ++++++++++++++++++++++-----------------
1 file changed, 36 insertions(+), 29 deletions(-)

diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index ea56f4fb234e..9a7656d01d06 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -2008,6 +2008,40 @@ static void dwc3_gadget_disable_irq(struct dwc3 *dwc);
static void __dwc3_gadget_stop(struct dwc3 *dwc);
static int __dwc3_gadget_start(struct dwc3 *dwc);

+static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
+{
+ u32 count;
+
+ dwc->connected = false;
+
+ /*
+ * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a
+ * Section 4.1.8 Table 4-7, it states that for a device-initiated
+ * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
+ * command for any active transfers" before clearing the RunStop
+ * bit.
+ */
+ dwc3_stop_active_transfers(dwc);
+ __dwc3_gadget_stop(dwc);
+
+ /*
+ * In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a
+ * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the
+ * "software needs to acknowledge the events that are generated
+ * (by writing to GEVNTCOUNTn) while it is waiting for this bit
+ * to be set to '1'."
+ */
+ count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
+ count &= DWC3_GEVNTCOUNT_MASK;
+ if (count > 0) {
+ dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
+ dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) %
+ dwc->ev_buf->length;
+ }
+
+ return dwc3_gadget_run_stop(dwc, false, false);
+}
+
static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
{
struct dwc3 *dwc = gadget_to_dwc(g);
@@ -2064,33 +2098,7 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
spin_lock_irqsave(&dwc->lock, flags);

if (!is_on) {
- u32 count;
-
- dwc->connected = false;
- /*
- * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
- * Section 4.1.8 Table 4-7, it states that for a device-initiated
- * disconnect, the SW needs to ensure that it sends "a DEPENDXFER
- * command for any active transfers" before clearing the RunStop
- * bit.
- */
- dwc3_stop_active_transfers(dwc);
- __dwc3_gadget_stop(dwc);
-
- /*
- * In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
- * Section 1.3.4, it mentions that for the DEVCTRLHLT bit, the
- * "software needs to acknowledge the events that are generated
- * (by writing to GEVNTCOUNTn) while it is waiting for this bit
- * to be set to '1'."
- */
- count = dwc3_readl(dwc->regs, DWC3_GEVNTCOUNT(0));
- count &= DWC3_GEVNTCOUNT_MASK;
- if (count > 0) {
- dwc3_writel(dwc->regs, DWC3_GEVNTCOUNT(0), count);
- dwc->ev_buf->lpos = (dwc->ev_buf->lpos + count) %
- dwc->ev_buf->length;
- }
+ ret = dwc3_gadget_soft_disconnect(dwc);
} else {
/*
* In the Synopsys DWC_usb31 1.90a programming guide section
@@ -2104,9 +2112,8 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)

dwc3_event_buffers_setup(dwc);
__dwc3_gadget_start(dwc);
+ ret = dwc3_gadget_run_stop(dwc, true, false);
}
-
- ret = dwc3_gadget_run_stop(dwc, is_on, false);
spin_unlock_irqrestore(&dwc->lock, flags);
enable_irq(dwc->irq_gadget);

--
2.35.1


\
 
 \ /
  Last update: 2022-09-26 12:38    [W:0.281 / U:0.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site