lkml.org 
[lkml]   [2022]   [Sep]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 5.19 115/207] iavf: Fix set max MTU size with port VLAN and jumbo frames
Date
From: Michal Jaron <michalx.jaron@intel.com>

[ Upstream commit 399c98c4dc50b7eb7e9f24da7ffdda6f025676ef ]

After setting port VLAN and MTU to 9000 on VF with ice driver there
was an iavf error
"PF returned error -5 (IAVF_ERR_PARAM) to our request 6".

During queue configuration, VF's max packet size was set to
IAVF_MAX_RXBUFFER but on ice max frame size was smaller by VLAN_HLEN
due to making some space for port VLAN as VF is not aware whether it's
in a port VLAN. This mismatch in sizes caused ice to reject queue
configuration with ERR_PARAM error. Proper max_mtu is sent from ice PF
to VF with GET_VF_RESOURCES msg but VF does not look at this.

In iavf change max_frame from IAVF_MAX_RXBUFFER to max_mtu
received from pf with GET_VF_RESOURCES msg to make vf's
max_frame_size dependent from pf. Add check if received max_mtu is
not in eligible range then set it to IAVF_MAX_RXBUFFER.

Fixes: dab86afdbbd1 ("i40e/i40evf: Change the way we limit the maximum frame size for Rx")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/ethernet/intel/iavf/iavf_virtchnl.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
index 1603e99bae4a..498797a0a0a9 100644
--- a/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
+++ b/drivers/net/ethernet/intel/iavf/iavf_virtchnl.c
@@ -273,11 +273,14 @@ int iavf_get_vf_vlan_v2_caps(struct iavf_adapter *adapter)
void iavf_configure_queues(struct iavf_adapter *adapter)
{
struct virtchnl_vsi_queue_config_info *vqci;
- struct virtchnl_queue_pair_info *vqpi;
+ int i, max_frame = adapter->vf_res->max_mtu;
int pairs = adapter->num_active_queues;
- int i, max_frame = IAVF_MAX_RXBUFFER;
+ struct virtchnl_queue_pair_info *vqpi;
size_t len;

+ if (max_frame > IAVF_MAX_RXBUFFER || !max_frame)
+ max_frame = IAVF_MAX_RXBUFFER;
+
if (adapter->current_op != VIRTCHNL_OP_UNKNOWN) {
/* bail because we already have a command pending */
dev_err(&adapter->pdev->dev, "Cannot configure queues, command %d pending\n",
--
2.35.1


\
 
 \ /
  Last update: 2022-09-26 14:07    [W:0.690 / U:0.576 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site