lkml.org 
[lkml]   [2022]   [Sep]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v2 0/2] Add Omnivision OV4689 image sensor driver
Date

Hi Dave,

On 2022-09-22 at 11:43 +01, Dave Stevenson <dave.stevenson@raspberrypi.com> wrote:

> Hi Mikhail & Sakari
>
> On Thu, 22 Sept 2022 at 10:55, Sakari Ailus
> <sakari.ailus@linux.intel.com> wrote:
>>
>> Hi Mikhail,
>>
>> On Sun, Sep 11, 2022 at 11:01:33PM +0300, Mikhail Rudenko wrote:
>> > Hello,
>> >
>> > this series implements support for Omnivision OV4689 image
>> > sensor. The Omnivision OV4689 is a high performance, 1/3-inch, 4
>> > megapixel image sensor. Ihis chip supports high frame rate speeds up
>> > to 90 fps at 2688x1520 resolution. It is programmable through an I2C
>> > interface, and sensor output is sent via 1/2/4 lane MIPI CSI-2
>> > connection.
>> >
>> > The driver is based on Rockchip BSP kernel [1]. It implements 4-lane CSI-2
>> > and single 2688x1520 @ 30 fps mode. The driver was tested on Rockchip
>> > 3399-based FriendlyElec NanoPi M4 board with MCAM400 camera module.
>> >
>> > While porting the driver, I stumbled upon two issues:
>> >
>> > (1) In the original driver, horizontal total size (HTS) was set to a
>> > value (2584) lower then the frame width (2688), resulting in negative
>> > hblank. In this driver, I increased HTS to 2688, but fps dropped from
>> > 29.88 to 28.73. What is the preferred way to handle this?
>>
>> If horizontal total size is less than the frame width, something is
>> certainly wrong there. You can't have negative horizontal blanking. Neither
>> it can be zero.
>
> Something certainly seems odd.
>
> To continue my thoughts from earlier in this patch set, Omnivision's
> Product Brief [1] states:
> The 1/3-inch OV4689 can capture full-resolution 4-megapixel high
> definition (HD) video at 90 frames per second (fps), 1080p HD at 120
> fps, and binned 720p HD at 180 fps
>
> The datasheet section 2.1 states:
> The OV4689 color image sensor is a high performance, 4 megapixel RAW
> image sensor that delivers 2688x1520 at 90 fps using OmniBSI-2™ pixel
> technology.
>
> So 4MP 90fps or 1080p120 should be achievable somehow.
>
> 2688x1520 @ 90fps is 367.7MPix/s, and that tallies quite nicely with
> table 2-9 listing the DAC PLL speed limitation of 360-378MHz. Exactly
> how that is then converted into PCLK or SCLK is unclear.
> Ideally you'd be able to contact an Omnivision FAE to confirm, but
> that means you need to be buying modules directly from them or
> otherwise have a business relationship.
> I do note that there is an NVidia Tegra driver for OV4689 at [2]. I
> wonder if analysis of that would reveal anything.
>
> I have just been looking at the ov9282 driver and the timings don't
> tally there either - configure it for 60fps and you get 30fps. The
> TIMING_HTS register appears to be in units of 2 pixels. The default is
> 0x2d8 (728 decimal) on a 1280x720 mode, but consider it as units of 2
> pixels and HTS of 1456 (1280 active and hblank of 176) does match up.
> It works in the general case too.
>
> Looking at the OV4689 datasheet again, the default for TIMING_HTS
> (0x380c/d) is 0x5f8 (1528 decimal) when HOUTPUT_SIZE (0x3808/9) is
> 0x1200 (4608 decimal). Whilst there are no guarantees that default
> register settings will stream in any sensible form, it does imply
> TIMING_HTS is not in units of 1 pixel, and potentially 4 pixels.
> From the Rockchip BSP driver it plainly does stream at 30 (or 29.88)
> fps with TIMING_HTS < HOUTPUT_SIZE, so a quick test of reducing it
> further would be worthwhile. What does the default of 0x2d8 give you
> as a frame rate, and are the images correct?

Thanks for sharing this! Actually, I'm going to do some experimentation
with these registers next weekend, and post the result here.

> Just some thoughts.
> Dave

--
Best regards,
Mikhail Rudenko

\
 
 \ /
  Last update: 2022-09-22 17:23    [W:0.074 / U:0.672 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site