lkml.org 
[lkml]   [2022]   [Sep]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [RFC PATCH 4/5] iio: accel: Support Kionix/ROHM KX022A accelerometer
Date
On 9/21/22 14:45, Matti Vaittinen wrote:
> KX022A is a 3-axis Accelerometer from ROHM/Kionix. The senor features
> include variable ODRs, I2C and SPI control, FIFO/LIFO with watermark IRQ,
> tap/motion detection, wake-up & back-to-sleep events, four acceleration
> ranges (2, 4, 8 and 16g) and probably some other cool fatures.
>
> Add support for the basic accelerometer features such as getting the
> acceleration data via IIO. (raw reads, triggered buffer [data-ready] or
> using the WMI IRQ).
>
> Important things to be added include the double-tap, motion
> detection and wake-up as well as the runtime power management.
>
> NOTE: Filling-up the hardware FIFO should be avoided. During my testing
> I noticed that filling up the hardware FIFO might mess-up the sample
> count. My sensor ended up in a state where amount of data in FIFO was
> reported to be 0xff bytes, which equals to 42,5 samples. Specification
> says the FIFO can hold maximum of 41 samples in HiRes mode. Also, at
> least once the FIFO was stuck in a state where reading data from
> hwardware FIFO did not decrease the amount of data reported to be in the
> FIFO - eg. FIFO was "stuck". The code has now an error count and 10
> reads with invalid FIFO data count will cause the fifo contents to be
> dropped.
>
> Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
> ---

//snip

> diff --git a/drivers/iio/accel/kionix-kx022a.c b/drivers/iio/accel/kionix-kx022a.c

//snip

> +static int kx022a_write_raw(struct iio_dev *idev,
> + struct iio_chan_spec const *chan,
> + int val, int val2, long mask)
> +{
> + struct kx022a_data *data = iio_priv(idev);
> + int ret;
> +
> + /*
> + * We should not allow changing scale or frequency when FIFO is running
> + * as it will mess the timestamp/scale for samples existing in the
> + * buffer. If this turns out to be an issue we can later change logic
> + * to internally flush the fifo before reconfiguring so the samples in
> + * fifo keep matching the freq/scale settings. (Such setup could cause
> + * issues if users trust the watermark to be reached within known
> + * time-limit).
> + */
> + mutex_lock(&data->mutex);
> + if (iio_buffer_enabled(idev)) {
> + ret = -EBUSY;
> + goto unlock_out;
> + }
> + switch (mask) {
> + case IIO_CHAN_INFO_SAMP_FREQ:
> + ret = kx022a_find_tuple_index(&kx022a_accel_samp_freq_table[0],
> + ARRAY_SIZE(kx022a_accel_samp_freq_table),
> + val, val2);
> + /* Configure if we found valid ODR */
> + if (ret >= 0) {
> + int odr = ret;
> +
> + ret = __kx022a_turn_off_unlocked(data);
> + if (ret)
> + goto unlock_out;
> +
> + ret = regmap_update_bits(data->regmap, KX022A_REG_ODCNTL,
> + KX022A_MASK_ODR, odr);
> + data->odr_ns = kx022a_odrs[odr];
> + __kx022a_turn_on_unlocked(data);
> + }
> + break;
> + case IIO_CHAN_INFO_SCALE:
> + ret = kx022a_find_tuple_index(&kx022a_scale_table[0],
> + ARRAY_SIZE(kx022a_scale_table),
> + val, val2);
> + /* Configure if we found valid scale */
> + if (ret >= 0) {
> + ret = __kx022a_turn_off_unlocked(data);
> + if (ret)
> + goto unlock_out;
> +
> + ret = regmap_update_bits(data->regmap, KX022A_REG_CNTL,
> + KX022A_MASK_GSEL,
> + ret << KX022A_GSEL_SHIFT);
> + __kx022a_turn_on_unlocked(data);
> + }

I did a last minute change to the locking here. As a result I missed the
break causing -EINVAL to be returned for scale setting. The build bot
pinged me about it :) Will be fixed when I respin this!

> + default:
> + ret = -EINVAL;
> + }
> +
> +unlock_out:
> + mutex_unlock(&data->mutex);
> +
> + return ret;
> +}
> +
Yours,
--Matti

--
Matti Vaittinen
Linux kernel developer at ROHM Semiconductors
Oulu Finland

~~ When things go utterly wrong vim users can always type :help! ~~
\
 
 \ /
  Last update: 2022-09-21 21:19    [W:0.099 / U:0.424 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site