lkml.org 
[lkml]   [2022]   [Sep]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] arm64, kdump: enforce to take 4G as the crashkernel low memory end
On Wed, Aug 31, 2022 at 10:29:39PM +0800, Baoquan He wrote:
> On 08/31/22 at 10:37am, Mike Rapoport wrote:
> > On Sun, Aug 28, 2022 at 08:55:44AM +0800, Baoquan He wrote:
> > >
> > > Solution:
> > > =========
> > > To fix the problem, we should always take 4G as the crashkernel low
> > > memory end in case CONFIG_ZONE_DMA or CONFIG_ZONE_DMA32 is enabled.
> > > With this, we don't need to defer the crashkernel reservation till
> > > bootmem_init() is called to set the arm64_dma_phys_limit. As long as
> > > memblock init is done, we can conclude what is the upper limit of low
> > > memory zone.
> > >
> > > 1) both CONFIG_ZONE_DMA or CONFIG_ZONE_DMA32 are disabled or memblock_start_of_DRAM() > 4G
> > > limit = PHYS_ADDR_MAX+1 (Corner cases)
> >
> > Why these are corner cases?
> > The case when CONFIG_ZONE_DMA or CONFIG_ZONE_DMA32 are disabled is the
> > simplest one because it does not require the whole dancing around
> > arm64_dma_phys_limit initialization.
> >
> > And AFAIK, memblock_start_of_DRAM() > 4G is not uncommon on arm64, but it
> > does not matter for device DMA addressing.
>
> Thanks for reviewing.
>
> I could be wrong and have misunderstanding about corner case.
>
> With my understanding, both ZONE_DMA and ZONE_DMA32 are enabled by
> default in kernel. And on distros, I believe they are on too. The both
> ZONE_DMA and ZONE_DMA32 disabled case should only exist on one specific
> product, and the memblock_start_of_DRAM() > 4G case too. At least, I
> haven't seen one in our LAB. What I thought the non generic as corner
> case could be wrong. I will change that phrasing.
>
> mm/Kconfig:
> config ZONE_DMA
> bool "Support DMA zone" if ARCH_HAS_ZONE_DMA_SET
> default y if ARM64 || X86
>
> config ZONE_DMA32
> bool "Support DMA32 zone" if ARCH_HAS_ZONE_DMA_SET
> depends on !X86_32
> default y if ARM64

My point was that the cases with ZONE_DMA/DMA32 disabled or with RAM above
4G do not require detection of arm64_dma_phys_limit before reserving the
crash kernel, can use predefined constants and are simple to handle.

> > The actual corner cases are systems with ZONE_DMA/DMA32 and with <32 bits
> > limit for device DMA addressing (e.g RPi 4). I think the changelog should
>
> Right, RPi4's 30bit DMA addressing device is corner case.
>
> > mention that to use kdump on these devices user must specify
> > crashkernel=X@Y
>
> Makes sense. I will add words in log, and add sentences to
> mention that in code comment or some place of document.
> Thanks for advice.
>
> >
> > > 2) CONFIG_ZONE_DMA or CONFIG_ZONE_DMA32 are enabled:
> > > limit = 4G (generic case)
> > >

...

> > > +static phys_addr_t __init crash_addr_low_max(void)
> > > +{
> > > + phys_addr_t low_mem_mask = U32_MAX;
> > > + phys_addr_t phys_start = memblock_start_of_DRAM();
> > > +
> > > + if ((!IS_ENABLED(CONFIG_ZONE_DMA) && !IS_ENABLED(CONFIG_ZONE_DMA32)) ||
> > > + (phys_start > U32_MAX))
> > > + low_mem_mask = PHYS_ADDR_MAX;
> > > +
> > > + return min(low_mem_mask, memblock_end_of_DRAM() - 1) + 1;
> >
> > Since RAM frequently starts on non-zero address the limit for systems with
> > ZONE_DMA/DMA32 should be memblock_start_of_DRAM() + 4G. There is no need to
>
> It may not be right for memblock_start_of_DRAM(). On most of arm64
> servers I ever tested, their memblock usually starts from a higher
> address, but not zero which is like x86. E.g below memory ranges printed
> on an ampere-mtsnow-altra system, the starting addr is 0x83000000. With
> my understanding, DMA addressing bits correspond to the cpu logical
> address range devices can address. So memblock_start_of_DRAM() + 4G
> seems not right for normal system, and not right for system which
> starting physical address is above 4G. I refer to max_zone_phys() of
> arch/arm64/mm/init.c when implementing crash_addr_low_max(). Please
> correct me if I am wrong.

My understanding was that no matter where DRAM starts, the first 4G would
be accessible by 32-bit devices, but I maybe wrong as well :)

I haven't notice you used max_zone_phys() as a reference. Wouldn't it be
simpler to just call it from crash_addr_low_max():

static phys_addr_t __init crash_addr_low_max(void)
{
return max_zone_phys(32);
}

--
Sincerely yours,
Mike.

\
 
 \ /
  Last update: 2022-09-01 09:29    [W:0.062 / U:0.160 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site