lkml.org 
[lkml]   [2022]   [Aug]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 1/2] clk: qcom: gcc-sc7180: Keep the USB GDSC always on
On Mon, Aug 29, 2022 at 01:42:02PM +0530, Rajendra Nayak wrote:
>
> On 8/26/2022 8:10 AM, Bjorn Andersson wrote:
> > On Thu, Aug 25, 2022 at 06:21:58PM -0700, Matthias Kaehlcke wrote:
> > > When the GDSC is disabled during system suspend USB is broken on
> > > sc7180 when the system resumes. Mark the GDSC as always on to
> > > make sure USB still works after system suspend.
> > >
> > > Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
> >
> > Rajendra, where you able to find some time to look into take the GDSC
> > into retention state? Do you suggest that I merge these two patches for
> > now?
> >
>
> Hi Bjorn, based on my experiments to support retention on sc7280 these are
> some of my findings
>
> On Platforms which support CX retention (for example sc7180/sc7280) instead of
> CX PowerCollapse (PC), We can leave the GDSC turned ON. When CX transitions to RET state
> the GDSC goes into retention too (some controller state is retained) and USB wakeups work.
>
> On platforms which support CX PC, just leaving the GDSC
> turned ON will not help since the GDSC will also transition to OFF state
> when we enter CX PC, hence wake-ups from USB won't work.
> For such platforms we need to make sure gdsc_force_mem_on() is called
> and cxcs (* @cxcs: offsets of branch registers to toggle mem/periph bits in)
> are populated correctly, while leaving the GDSC turned ON.
> This will make sure usb gdsc transitions from being powered by CX to MX
> when CX hits PC and we still get USB wakeups to work.
> So in short we could do the same thing that this patch does on those
> platforms too with additionally populating the right cxcs entries and it
> should just work fine.
>
> Now the problem that I see with this approach is not with getting USB wakeups
> to work in suspend, but with supporting performance state voting when
> USB is active.
> The last conclusion we had on that [1] was to model usb_gdsc as a subdomain of CX,
> so if we do that and we model usb_gdsc as something that supports ALWAYS_ON,
> we would _never_ drop the CX vote and prevent CX from going down (either to ret
> or pc)
>
> The only way I think we can solve both the USB wakeups and performance state
> needs (with usb_gdsc as a subdomain of CX) is if we can model a RET state for gdsc
> which sets the mem/periph bits while leaving the GDSC ON (Today the RET state sets
> the mem/periph bits but turns the GDSC OFF)
>
> That would mean a change in gdsc.c like this
> ---
>
> diff --git a/drivers/clk/qcom/gdsc.c b/drivers/clk/qcom/gdsc.c
> index d3244006c661..0fe017ba901b 100644
> --- a/drivers/clk/qcom/gdsc.c
> +++ b/drivers/clk/qcom/gdsc.c
> @@ -368,6 +368,10 @@ static int _gdsc_disable(struct gdsc *sc)
> if (sc->pwrsts & PWRSTS_OFF)
> gdsc_clear_mem_on(sc);
>
> + /* If the GDSC supports RET, do not explicitly power it off */
> + if (sc->pwrsts & PWRSTS_RET)
> + return 0;
> +
> ret = gdsc_toggle_logic(sc, GDSC_OFF);
> if (ret)
> return ret;
>
>
> So with that change, we would then not need the ALWAYS_ON flag set for usb gdsc,
> instead we would update the .pwrsts to PWRSTS_RET_ON instead of PWRSTS_OFF_ON,
> and that should make both usb wake-ups to work and we can still have the usb_gdsc as
> a subdomain of CX for performance state voting.

Krishna and I confirmed that this works from the USB side for sc7180 and sc7280.

\
 
 \ /
  Last update: 2022-08-30 20:44    [W:0.076 / U:0.868 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site