lkml.org 
[lkml]   [2022]   [Aug]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] ARM: dts: lan966x: add support for pcb8290
The 08/23/2022 07:11, Claudiu Beznea - M18063 wrote:

Hi Claudiu,

> > +&gpio {
> > + miim_a_pins: mdio-pins {
> > + /* MDC, MDIO */
> > + pins = "GPIO_28", "GPIO_29";
> > + function = "miim_a";
> > + };
> > +
> > + pps_out_pins: pps-out-pins {
>
> Can you also document this one as well? I can do it while applying if you
> provide the strings.

Yes, I will do that.
I will send a new version because I have seen that there is also a small
error in the commit message.

>
> > + pins = "GPIO_38";
> > + function = "ptpsync_3";
> > + };
> > +
> > + ptp_ext_pins: ptp-ext-pins {
>
> Ditto
>
> Thank you,
> Claudiu Beznea
>
> > + pins = "GPIO_35";
> > + function = "ptpsync_0";
> > + };
> > +
> > + udc_pins: ucd-pins {
> > + /* VBUS_DET B */
> > + pins = "GPIO_8";
> > + function = "usb_slave_b";
> > + };
> > +};
> > +
> > +&mdio0 {
> > + pinctrl-0 = <&miim_a_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +
> > + ext_phy0: ethernet-phy@7 {
> > + reg = <7>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + ext_phy1: ethernet-phy@8 {
> > + reg = <8>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + ext_phy2: ethernet-phy@9 {
> > + reg = <9>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + ext_phy3: ethernet-phy@10 {
> > + reg = <10>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + ext_phy4: ethernet-phy@15 {
> > + reg = <15>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + ext_phy5: ethernet-phy@16 {
> > + reg = <16>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + ext_phy6: ethernet-phy@17 {
> > + reg = <17>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + ext_phy7: ethernet-phy@18 {
> > + reg = <18>;
> > + coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > + };
> > +};
> > +
> > +&port0 {
> > + reg = <2>;
> > + phy-handle = <&ext_phy2>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 0 SERDES6G(1)>;
> > + status = "okay";
> > +};
> > +
> > +&port1 {
> > + reg = <3>;
> > + phy-handle = <&ext_phy3>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 1 SERDES6G(1)>;
> > + status = "okay";
> > +};
> > +
> > +&port2 {
> > + reg = <0>;
> > + phy-handle = <&ext_phy0>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 2 SERDES6G(1)>;
> > + status = "okay";
> > +};
> > +
> > +&port3 {
> > + reg = <1>;
> > + phy-handle = <&ext_phy1>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 3 SERDES6G(1)>;
> > + status = "okay";
> > +};
> > +
> > +&port4 {
> > + reg = <6>;
> > + phy-handle = <&ext_phy6>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 4 SERDES6G(2)>;
> > + status = "okay";
> > +};
> > +
> > +&port5 {
> > + reg = <7>;
> > + phy-handle = <&ext_phy7>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 5 SERDES6G(2)>;
> > + status = "okay";
> > +};
> > +
> > +&port6 {
> > + reg = <4>;
> > + phy-handle = <&ext_phy4>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 6 SERDES6G(2)>;
> > + status = "okay";
> > +};
> > +
> > +&port7 {
> > + reg = <5>;
> > + phy-handle = <&ext_phy5>;
> > + phy-mode = "qsgmii";
> > + phys = <&serdes 7 SERDES6G(2)>;
> > + status = "okay";
> > +};
> > +
> > +&serdes {
> > + status = "okay";
> > +};
> > +
> > +&switch {
> > + pinctrl-0 = <&pps_out_pins>, <&ptp_ext_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > +&udc {
> > + pinctrl-0 = <&udc_pins>;
> > + pinctrl-names = "default";
> > + atmel,vbus-gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
> > + status = "okay";
> > +};
>

--
/Horatiu

\
 
 \ /
  Last update: 2022-08-23 22:04    [W:0.075 / U:1.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site