lkml.org 
[lkml]   [2022]   [Aug]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net-next v2 13/17] net: dsa: microchip: ksz9477: use internal_phy instead of phy_port_cnt
Date
With code refactoring was introduced new variable internal_phy. Let's
use it.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
drivers/net/dsa/microchip/ksz9477.c | 20 +++++++-------------
1 file changed, 7 insertions(+), 13 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c
index cb5bd0ceb8df4..2982c8cb0983c 100644
--- a/drivers/net/dsa/microchip/ksz9477.c
+++ b/drivers/net/dsa/microchip/ksz9477.c
@@ -291,7 +291,7 @@ int ksz9477_r_phy(struct ksz_device *dev, u16 addr, u16 reg, u16 *data)
* For RGMII PHY there is no way to access it so the fixed PHY should
* be used. For SGMII PHY the supporting code will be added later.
*/
- if (addr >= dev->phy_port_cnt) {
+ if (!dev->info->internal_phy[addr]) {
struct ksz_port *p = &dev->ports[addr];

switch (reg) {
@@ -339,7 +339,7 @@ int ksz9477_r_phy(struct ksz_device *dev, u16 addr, u16 reg, u16 *data)
int ksz9477_w_phy(struct ksz_device *dev, u16 addr, u16 reg, u16 val)
{
/* No real PHY after this. */
- if (addr >= dev->phy_port_cnt)
+ if (!dev->info->internal_phy[addr])
return 0;

return ksz_pwrite16(dev, addr, 0x100 + (reg << 1), val);
@@ -888,7 +888,7 @@ static phy_interface_t ksz9477_get_interface(struct ksz_device *dev, int port)
phy_interface_t interface;
bool gbit;

- if (port < dev->phy_port_cnt)
+ if (dev->info->internal_phy[port])
return PHY_INTERFACE_MODE_NA;

gbit = ksz_get_gbit(dev, port);
@@ -995,7 +995,7 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
/* enable 802.1p priority */
ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_PRIO_ENABLE, true);

- if (port < dev->phy_port_cnt) {
+ if (dev->info->internal_phy[port]) {
/* do not force flow control */
ksz_port_cfg(dev, port, REG_PORT_CTRL_0,
PORT_FORCE_TX_FLOW_CTRL | PORT_FORCE_RX_FLOW_CTRL,
@@ -1018,7 +1018,7 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port)
ksz9477_cfg_port_member(dev, port, member);

/* clear pending interrupts */
- if (port < dev->phy_port_cnt)
+ if (dev->info->internal_phy[port])
ksz_pread16(dev, port, REG_PORT_PHY_INT_ENABLE, &data16);
}

@@ -1081,7 +1081,7 @@ void ksz9477_config_cpu_port(struct dsa_switch *ds)

ksz_port_stp_state_set(ds, i, BR_STATE_DISABLED);
p->on = 1;
- if (i < dev->phy_port_cnt)
+ if (dev->info->internal_phy[i])
p->phy = 1;
if (dev->chip_id == 0x00947700 && i == 6) {
p->sgmii = 1;
@@ -1177,15 +1177,9 @@ int ksz9477_switch_init(struct ksz_device *dev)
if (ret)
return ret;

- /* Number of ports can be reduced depending on chip. */
- dev->phy_port_cnt = 5;
-
- if (dev->chip_id == KSZ9893_CHIP_ID) {
+ if (dev->chip_id == KSZ9893_CHIP_ID)
dev->features |= IS_9893;

- dev->phy_port_cnt = 2;
- }
-
return 0;
}

--
2.30.2
\
 
 \ /
  Last update: 2022-08-22 13:06    [W:0.119 / U:0.000 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site