lkml.org 
[lkml]   [2022]   [Aug]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 net-next 3/6] drivers: net: dsa: add locked fdb entry flag to drivers
On 2022-08-21 09:08, Ido Schimmel wrote:
> On Fri, Aug 19, 2022 at 11:51:11AM +0200, netdev@kapio-technology.com
> wrote:
>> On 2022-08-14 16:55, Ido Schimmel wrote:
>> > On Fri, Aug 12, 2022 at 02:29:48PM +0200, netdev@kapio-technology.com
>> > wrote:
>> > > On 2022-08-11 13:28, Ido Schimmel wrote:
>> > >
>> > > > > > I'm talking about roaming, not forwarding. Let's say you have a locked
>> > > > > > entry with MAC X pointing to port Y. Now you get a packet with SMAC X
>> > > > > > from port Z which is unlocked. Will the FDB entry roam to port Z? I
>> > > > > > think it should, but at least in current implementation it seems that
>> > > > > > the "locked" flag will not be reset and having locked entries pointing
>> > > > > > to an unlocked port looks like a bug.
>>
>> I have made the locked entries sticky in the bridge, so that they
>> don't move
>> to other ports.
>
> Please make sure that this design choice is explained in the commit
> message. To be clear, it cannot be "this is how device X happens to
> work".
>

The real issue I think is that the locked entry should mask the MAC
address involved (as the description I gave for zero-DPV entries and
actually also storm prevention entries ensure), so that there is no
forwarding to the address on any port, otherwise it will allow one-way
traffic to a host that is not trusted. Thus flooding of unknown unicast
on a locked port should of course be disabled ('flood off'), so that
there is no way of sending to an unauthorized silent host behind the
locked port.

The issue with the locked entry appearing on another SW bridge port from
where it originated, I think is more of a cosmetic bug, though I could
be mistaken. But adding the sticky flag to locked entries ensures that
they do not move to another port.

This of course does that instant roaming is not possible, but I think
that the right approach is to use the ageing out of entries to allow the
station move/roaming.

The case of unwanted traffic to a MAC behind a locked port with a locked
entry is what I would regard as more worthy of a selftest. The sticky
flag I know will ensure that the locked entries do not move to other
ports, and since it is only in the bridge this can be tested (e.g. using
'bridge fdb show dev DEV'), I think that the test would be superfluos.
What do you think of that and my other consideration for a test?


>> I have now created the flag to enable Mac-Auth/MAB with iproute2:
>> bridge link set dev DEV macauth on|off
>
> You have 'macauth' here, but 'mab' in the output below. They need to
> match. I prefer the latter unless you have a good reason to use
> 'macauth'.
>
>>
>> with the example output from 'bridge -d link show dev DEV' when
>> macauth is
>> enabled:
>> 1: ethX: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br0 state
>> forwarding priority 32 cost 19
>> hairpin off guard off root_block off fastleave off learning on
>> flood off
>> mcast_flood on bcast_flood on mcast_router 1 mcast_to_unicast off
>> neigh_suppress off vlan_tunnel off isolated off locked mab on
>>
>> The flag itself in the code is called BR_PORT_MACAUTH.
>>
>> >
>> > Fine by me, but I'm not sure everyone agrees.

I will change it in iproute2 to:
bridge link set dev DEV mab on|off

\
 
 \ /
  Last update: 2022-08-21 15:44    [W:0.849 / U:0.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site