lkml.org 
[lkml]   [2022]   [Aug]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v26 0/4] media: mediatek: support mdp3 on mt8183 platform
Date
Change since v25:
- Add more COMPILE_TEST config in MDP3 Kconfig
- Adjust unnecessary log level in "mdp_m2m_s_selection" function to
avoid spamming the kernel log for userspace errors.
- The v4l2-compliance test results list is as follows:

v4l2-compliance 1.23.0-4942, 32 bits, 32-bit time_t
v4l2-compliance SHA: 4cf258c24026 2022-07-28 15:43:45

Compliance test for mtk-mdp3 device /dev/video0:

Driver Info:
Driver name : mtk-mdp3
Card type : MediaTek MDP3
Bus info : platform:14001000.mdp3-rdma0
Driver version : 6.0.0
Capabilities : 0x84204000
Video Memory-to-Memory Multiplanar
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x04204000
Video Memory-to-Memory Multiplanar
Streaming
Extended Pix Format
Required ioctls:
test VIDIOC_QUERYCAP: OK
test invalid ioctls: OK
Allow for multiple opens:
test second /dev/video0 open: OK
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
test for unlimited opens: OK
Debug ioctls:
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK (Not Supported)
Input ioctls:
test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported)
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 0 Audio Inputs: 0 Tuners: 0
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK (Not Supported)
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
test VIDIOC_G/S_EDID: OK (Not Supported)
Control ioctls:
test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK
test VIDIOC_QUERYCTRL: OK
test VIDIOC_G/S_CTRL: OK
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 4 Private Controls: 0
Format ioctls:
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK
test VIDIOC_G/S_PARM: OK (Not Supported)
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK
test VIDIOC_TRY_FMT: OK
test VIDIOC_S_FMT: OK
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
test Cropping: OK
test Composing: OK
test Scaling: OK
Codec ioctls:
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls:
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK
test VIDIOC_EXPBUF: OK
test Requests: OK (Not Supported)
test TIME32/64: OK
Test input 0:
Streaming ioctls:
test read/write: OK (Not Supported)
test blocking wait: OK
<snip>
test MMAP (no poll): OK
<snip>
test MMAP (select): OK
<snip>
test MMAP (epoll): OK
test USERPTR (no poll): OK (Not Supported)
test USERPTR (select): OK (Not Supported)
test DMABUF: Cannot test, specify --expbuf-device
Stream using all formats:
<snip>
Total for mtk-mdp3 device /dev/video0: 1592, Succeeded: 1592, Failed: 0, Warnings: 0

Change since v24:
- Rebase on v6.0-rc1.

Change since v23:
- Rebase on linux-next.
- Fix compilation error.

Change since v22:
- Rebase on linux-next.
- Fix typo about MDP3 in Kconfig.
- Adjust some non-essential logs to lower levels.

Change since v21:
- Rebase on linux-next.
- Following Hans suggestion, remove redundant kernel logs and
revise a few non-functional code to make it clearer.
- Remove API abuse to set plane size.
- Added VPU send message failure error code for previous shortages.

Change since v20:
- Rebase on linux-next.
- Move the MDP3 GCE events to the corresponding node and adjust the
relevant driver settings.

Change since v19:
- Rebase on linux-next.
- Export the function "mdp_cmdq_send" suggected by CK.
- Fix "Macro argument reuse" reported by checkpatch.pl

Change since v18:
- Rebase on linux-next.
- Adjust copyright date of MDP3 driver.
- Functions renaming as follows:
[1] is_output_disable() => is_output_disabled()
[2] mdp_component_init() => mdp_comp_config()
[3] mdp_component_deinit() => mdp_comp_destroy()
[4] mdp_comp_ctx_init() => mdp_comp_ctx_config()
[5] mdp_sub_comps_create() => mdp_comp_sub_create()
- Document MDP3 10-bit format descriptions in "mtk-mdp3-regs.c".
- Add error control for functions mdp_comp_clocks_on and mdp_comp_clock_on.
- Moved function "mtk_mutex_put" from function
"mdp_comp_destroy"(renamed from mdp_component_deinit) to avoid semantic ambiguity.
- For some allocated parameters, assign a value of NULL after freeing
to avoid the possibility of repeated use.
- Removed unnecessary timestamp pass flow.
- About parameters passed by the user in function "mdp_try_fmt_mplane", add relevant checks to
clamp them in a reasonable range to avoid the possibility of overflow

Change since v17:
- Depend on:
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=649104
- In response to future CMDQ api changes listed below:
https://patchwork.kernel.org/project/linux-mediatek/patch/20220608144055.27562-1-chunkuang.hu@kernel.org/
adjust CMDQ flush and callback flow in MDP3.

Change since v16:
- Rebased on v5.19-rc1
- Depend on:
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=646131
- In response to MUTEX changes, adjust API naming and parameters when
used in function "mdp_path_subfrm_require".
- Remove unnecessary MDP3 phandle in 8183 dts.

Change since v15:
- Depend on:
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=640926
- Split the bindings under ./soc/mediatek into a separate patch.
- Fix data abort in "mdp_auto_release_work"
- Adjust the steps in the function "mdp_cmdq_send" to make the error handling
more reasonable

Change since v14:
- Rebase on v5.18-rc6
- Depend on:
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=640926
- In response to CMDQ API change, replace the function "cmdq_pkt_flush_async"
with the standard APIs of mbox
- Fix the description of "mediatek,gce-client-reg" property in MDP3-related
bindings

Change since v13:
- Rebase on v5.18-rc4
- Depend on:
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=636041
- Remove advanced functionality about ISP settings for direct link cases.
- Remove the software designation in the mt8183 dts and
revise corresponding bindings.

Change since v12:
- Rebase on linux-next
- Depend on:
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=630948
- Remove messages related to routing information in MDP3, and leave the related
settings in MMSYS.
- Remove unnecessary phandle and redundant property in RDMA dt-binding and
adjust the corresponding driver.
- Revise MDP3 node name in dts.
- Removed unnecessary functions, mutex and work queue in MDP3 driver
- Fixed format mapping error for V4L2_PIX_FMT_RGB565X

Change since v11:
- Rebase on linux-next tag:next-20220316
- Depend on:
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=624281
- Remove redundant hardware index in data-binding suggested by Rob Herring.
- Referring to Rob Herring's suggestion to improve some descriptions in the
RDMA dt-binding
- Move MDP3 file folder from "./drive/media/platform/mtk-mdp3" to
"./driver/media/platform/mediatek/mdp3"
- Fixed the V4L2 and MDP color format mapping error in RGB565 which
checked by Benjamin Gaignard

Change since v10:
- The routing table needs to be discarded, and the calculation result
on the SCP side is used to write a suitable mux setting for
1 input port and 2 output ports.
- Adjust dts parsing flow to remove redundant HW IDs.
- Fix memory leak caused by no free path information in function "mdp_cmdq_send".

Change since v9:
- Keep only the MDP3 driver patches and split the remaining mmsys and
mutex patches into another mail.
- Move mutex mod settings to corresponding driver and make relevant adjustments
for this in MDP3 driver.
- Fix compile warning reported by kernel test robot.

Change since v8:
- Rebase on v5.16-rc2.
- Refer to Angelo's suggestion, adjust the register writing format to increase
readability and significance.
- Refer to Angelo's suggestion, adjust or reduce inappropriate debugging
messages.
- Refer to Rob Herring's suggestion to correct the the binding file
to make it with the specification.
- Fix compile warning reported by kernel test robot.

Change since v7:
- Rebase on v5.15-rc6.
- Revise several V4L2 M2M settings to pass v4l2-compliance test.
- Integrate those same component dt-binding documents of DRM and MDP, and
move them under the MMSYS domain.
- Split MMSYS and MUTEX into two different files according to
their functional properties.

Changes since v6:
- Refactor GCE event to corresponding node.
- Fix dt_binding_check fail.
- Fix compilation errors.

Changes since v5:
- Rebase on v5.14-rc6.
- Move MMSYS/Mutex settings to corresponding driver.
- Revise the software license description and copyright.
- Remove unnecessary enum. or definitions.
- Optimize platform/chip definition conditions.
- Use general printing functions instead of MDP3 private ones.
- Fix compile warning.

Changes since v4:
- Rebase on v5.13-rc1.
- Remove the CMDQ flush flow to match the CMDQ API change.
- Integrate four of MDP's direct-link subcomponents into MDP controller node
from syscon node to avoid illegal clock usage.
- Rewrite dt-binding in a JSON compatible subset of YAML
- Fix a bit of macro argument precedence.

Changes since v3:
- Rebase on v5.9-rc1.
- modify code for review comment from Rob Herring, cancel multiple nodes using
same register base situation.
- control IOMMU port through pm runtime get/put to DMA components' device.
- SCP(VPU) driver revision.
- stop queuing jobs(remove flush_workqueue()) after mdp_m2m_release().
- add computation of plane address with data_offset.
- fix scale ratio check issue.
- add default v4l2_format setting.

Changes since v2:
- modify code for review comment from Tomasz Figa & Alexandre Courbot
- review comment from Rob Herring will offer code revision in v4, due to
it's related to device node modification, will need to modify code
architecture

Changes since v1:
- modify code for CMDQ v3 API support
- EC ipi cmd migration
- fix compliance test fail item (m2m cmd with -f) due to there is two problem in
runing all format(-f) cmd:
1. out of memory before test complete
Due to capture buffer mmap (refcount + 1) after reqbuf but seems
no corresponding munmap called before device close.
There are total 12XX items(formats) in format test and each format
alloc 8 capture/output buffers.
2. unceasingly captureBufs() (randomly)
Seems the break statement didn't catch the count == 0 situation:
In v4l2-test-buffers.cpp, function: captureBufs()
...
count--;
if (!node->is_m2m && !count)
break;
Log is as attachment

Hi,

This patch is used to present Media Data Path 3 (MDP3)
which provided scaling and color format conversion.
support using GCE to write register in critical time limitation.
support V4L2 m2m device control.


Moudy Ho (4):
dt-binding: mediatek: add bindings for MediaTek MDP3 components
dt-binding: mediatek: add bindings for MediaTek CCORR and WDMA
arm64: dts: mt8183: add MediaTek MDP3 nodes
media: platform: mtk-mdp3: add MediaTek MDP3 driver

.../bindings/media/mediatek,mdp3-rdma.yaml | 95 ++
.../bindings/media/mediatek,mdp3-rsz.yaml | 77 ++
.../bindings/media/mediatek,mdp3-wrot.yaml | 80 ++
.../bindings/soc/mediatek/mediatek,ccorr.yaml | 68 ++
.../bindings/soc/mediatek/mediatek,wdma.yaml | 81 ++
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 63 +
drivers/media/platform/mediatek/Kconfig | 1 +
drivers/media/platform/mediatek/Makefile | 1 +
drivers/media/platform/mediatek/mdp3/Kconfig | 20 +
drivers/media/platform/mediatek/mdp3/Makefile | 6 +
.../platform/mediatek/mdp3/mdp_reg_ccorr.h | 19 +
.../platform/mediatek/mdp3/mdp_reg_rdma.h | 65 ++
.../platform/mediatek/mdp3/mdp_reg_rsz.h | 39 +
.../platform/mediatek/mdp3/mdp_reg_wdma.h | 47 +
.../platform/mediatek/mdp3/mdp_reg_wrot.h | 55 +
.../platform/mediatek/mdp3/mtk-img-ipi.h | 290 +++++
.../platform/mediatek/mdp3/mtk-mdp3-cmdq.c | 466 ++++++++
.../platform/mediatek/mdp3/mtk-mdp3-cmdq.h | 43 +
.../platform/mediatek/mdp3/mtk-mdp3-comp.c | 1031 +++++++++++++++++
.../platform/mediatek/mdp3/mtk-mdp3-comp.h | 186 +++
.../platform/mediatek/mdp3/mtk-mdp3-core.c | 357 ++++++
.../platform/mediatek/mdp3/mtk-mdp3-core.h | 94 ++
.../platform/mediatek/mdp3/mtk-mdp3-m2m.c | 724 ++++++++++++
.../platform/mediatek/mdp3/mtk-mdp3-m2m.h | 48 +
.../platform/mediatek/mdp3/mtk-mdp3-regs.c | 733 ++++++++++++
.../platform/mediatek/mdp3/mtk-mdp3-regs.h | 373 ++++++
.../platform/mediatek/mdp3/mtk-mdp3-vpu.c | 313 +++++
.../platform/mediatek/mdp3/mtk-mdp3-vpu.h | 78 ++
28 files changed, 5453 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/mediatek,mdp3-rdma.yaml
create mode 100644 Documentation/devicetree/bindings/media/mediatek,mdp3-rsz.yaml
create mode 100644 Documentation/devicetree/bindings/media/mediatek,mdp3-wrot.yaml
create mode 100644 Documentation/devicetree/bindings/soc/mediatek/mediatek,ccorr.yaml
create mode 100644 Documentation/devicetree/bindings/soc/mediatek/mediatek,wdma.yaml
create mode 100644 drivers/media/platform/mediatek/mdp3/Kconfig
create mode 100644 drivers/media/platform/mediatek/mdp3/Makefile
create mode 100644 drivers/media/platform/mediatek/mdp3/mdp_reg_ccorr.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mdp_reg_rdma.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mdp_reg_rsz.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mdp_reg_wdma.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mdp_reg_wrot.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-img-ipi.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-cmdq.c
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-cmdq.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-comp.c
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-comp.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-core.c
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-core.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-m2m.c
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-m2m.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-regs.c
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-regs.h
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-vpu.c
create mode 100644 drivers/media/platform/mediatek/mdp3/mtk-mdp3-vpu.h

--
2.18.0

\
 
 \ /
  Last update: 2022-08-19 10:56    [W:0.750 / U:0.432 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site