lkml.org 
[lkml]   [2022]   [Aug]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 1/4] media: mt9m111: add V4L2_CID_PIXEL_RATE support
Hi Marco

On Fri, Aug 19, 2022 at 09:56:15AM +0200, Marco Felsch wrote:
> Hi Jacopo,
>
> On 22-08-18, Jacopo Mondi wrote:
> > Hi Marco
> >
> > On Thu, Aug 18, 2022 at 04:47:09PM +0200, Marco Felsch wrote:
> > > Add support to report the PIXEL_RATE so a host or bridge device can ask
> > > the sensor.
> > >
> > > Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> > > ---
> > > drivers/media/i2c/mt9m111.c | 15 ++++++++++++++-
> > > 1 file changed, 14 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/drivers/media/i2c/mt9m111.c b/drivers/media/i2c/mt9m111.c
> > > index afc86efa9e3e..cdaf283e1309 100644
> > > --- a/drivers/media/i2c/mt9m111.c
> > > +++ b/drivers/media/i2c/mt9m111.c
> > > @@ -908,6 +908,8 @@ static int mt9m111_s_ctrl(struct v4l2_ctrl *ctrl)
> > > return mt9m111_set_test_pattern(mt9m111, ctrl->val);
> > > case V4L2_CID_COLORFX:
> > > return mt9m111_set_colorfx(mt9m111, ctrl->val);
> > > + case V4L2_CID_PIXEL_RATE:
> > > + return 0;
> >
> > By default PIXEL_RATE is read-only.
> > Do you get a call to s_ctrl for it ?
>
> You're absolutly right, we don't need to do this.
>
> > > }
> > >
> > > return -EINVAL;
> > > @@ -1249,6 +1251,7 @@ static int mt9m111_probe(struct i2c_client *client)
> > > {
> > > struct mt9m111 *mt9m111;
> > > struct i2c_adapter *adapter = client->adapter;
> > > + unsigned long mclk_rate;
> > > int ret;
> > >
> > > if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA)) {
> > > @@ -1271,6 +1274,13 @@ static int mt9m111_probe(struct i2c_client *client)
> > > if (IS_ERR(mt9m111->clk))
> > > return PTR_ERR(mt9m111->clk);
> > >
> > > + ret = clk_prepare_enable(mt9m111->clk);
> > > + if (ret < 0)
> > > + return ret;
> > > +
> >
> > Do you need to enable clock to read its rate ?
>
> Yes, accroding the API [1].
>
> [1] https://elixir.bootlin.com/linux/v6.0-rc1/source/include/linux/clk.h#L682

So weird! none of the drivers I checked do that. The most common
pattern is

clk = devm_clk_get();
rate = clk_get_rate(clk)
if (rate != RATE)
...

>
> > > + mclk_rate = clk_get_rate(mt9m111->clk);
> > > + clk_disable_unprepare(mt9m111->clk);
> > > +
> > > mt9m111->regulator = devm_regulator_get(&client->dev, "vdd");
> > > if (IS_ERR(mt9m111->regulator)) {
> > > dev_err(&client->dev, "regulator not found: %ld\n",
> > > @@ -1285,7 +1295,7 @@ static int mt9m111_probe(struct i2c_client *client)
> > > mt9m111->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE |
> > > V4L2_SUBDEV_FL_HAS_EVENTS;
> > >
> > > - v4l2_ctrl_handler_init(&mt9m111->hdl, 7);
> > > + v4l2_ctrl_handler_init(&mt9m111->hdl, 8);
> > > v4l2_ctrl_new_std(&mt9m111->hdl, &mt9m111_ctrl_ops,
> > > V4L2_CID_VFLIP, 0, 1, 1, 0);
> > > v4l2_ctrl_new_std(&mt9m111->hdl, &mt9m111_ctrl_ops,
> > > @@ -1309,6 +1319,9 @@ static int mt9m111_probe(struct i2c_client *client)
> > > BIT(V4L2_COLORFX_NEGATIVE) |
> > > BIT(V4L2_COLORFX_SOLARIZATION)),
> > > V4L2_COLORFX_NONE);
> > > + v4l2_ctrl_new_std(&mt9m111->hdl, &mt9m111_ctrl_ops, V4L2_CID_PIXEL_RATE,
> > > + mclk_rate, mclk_rate, 1, mclk_rate);
> > > +
> >
> > I don't have a datasheet but it seems a little weird that the mclk
> > frequency is the same as the pixel clock rate ?
>
> I see your confusion here. I can only speak for the MT9M131 device which
> is covered by this driver as well. This device is composed of a
> internal-sensor and a internal-isp. The internal-sensor is clocked by
> mclk/2 but the final image device/sensor output-fifo is clocked by mclk.

No PLL, no rate multiplier/divider ? Does this sensor only work with
one pixel rate that is defined by the input clock rate ?

> There are options to devide the output clock as well, but these options
> are not enabled yet. So yes, the pixel clock rate == mclk rate. To avoid

Ah ok

Could you share your setup mclk, resolution and frame rate to show how
the pixel rate and the mclk rate are related ?

> confusion I could rename the mclk_rate to extclk_rate but then clock
> request is not 100% correct since we are requesting a "mclk", this
> should be "extclk".

Doesn't really make a difference!
A comment in the code to explain what happens would help though!

>
> Regards,
> Marco
>
> > > mt9m111->subdev.ctrl_handler = &mt9m111->hdl;
> > > if (mt9m111->hdl.error) {
> > > ret = mt9m111->hdl.error;
> > > --
> > > 2.30.2
> > >
> >

\
 
 \ /
  Last update: 2022-08-19 10:17    [W:0.081 / U:0.124 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site