lkml.org 
[lkml]   [2022]   [Aug]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [Regression] ext4: changes to mb_optimize_scan cause issues on Raspberry Pi
Hi Stefan!

On Sat 06-08-22 11:50:28, Stefan Wahren wrote:
> Am 28.07.22 um 12:00 schrieb Jan Kara:
> > Hello!
> >
> > On Mon 18-07-22 15:29:47, Stefan Wahren wrote:
> > > i noticed that since Linux 5.18 (Linux 5.19-rc6 is still affected) i'm
> > > unable to run "rpi-update" without massive performance regression on my
> > > Raspberry Pi 4 (multi_v7_defconfig + CONFIG_ARM_LPAE). Using Linux 5.17 this
> > > tool successfully downloads the latest firmware (> 100 MB) on my development
> > > micro SD card (Kingston 16 GB Industrial) with a ext4 filesystem within ~ 1
> > > min. The same scenario on Linux 5.18 shows the following symptoms:
> > Thanks for report and the bisection!
> > > - download takes endlessly much time and leads to an abort by userspace in
> > > most cases because of the poor performance
> > > - massive system load during download even after download has been aborted
> > > (heartbeat LED goes wild)
> > OK, is it that the CPU is busy or are we waiting on the storage card?
> > Observing top(1) for a while should be enough to get the idea. (sorry, I'm
> > not very familiar with RPi so I'm not sure what heartbeat LED shows).
>
> My description wasn't precise. I mean the green ACT LED, which uses the LED
> heartbeat trigger:
>
> "This allows LEDs to be controlled by a CPU load average. The flash
> frequency is a hyperbolic function of the 1-minute load average."
>
> I'm not sure if it's CPU or IO driven load, here the top output in bad case:
>
> top - 08:44:17 up 43 min,  2 users,  load average: 5,02, 5,45, 5,17
> Tasks: 142 total,   1 running, 141 sleeping,   0 stopped,   0 zombie
> %Cpu(s):  0,4 us,  0,4 sy,  0,0 ni, 49,0 id, 50,2 wa,  0,0 hi, 0,0 si,  0,0
> st
> MiB Mem :   7941,7 total,   4563,1 free,    312,7 used,   3066,0 buff/cache
> MiB Swap:    100,0 total,    100,0 free,      0,0 used.   7359,6 avail Mem

OK, there's plenty of memory available, CPUs are mostly idle, the load is
likely created by tasks waiting for IO (which also contribute to load
despite not consuming CPU). Not much surprising here.

> > Can you run "iostat -x 1" while the download is running so that we can see
> > roughly how the IO pattern looks?
> >
> Here the output during download:
>
> Device            r/s     w/s     rkB/s     wkB/s   rrqm/s wrqm/s  %rrqm 
> %wrqm r_await w_await aqu-sz rareq-sz wareq-sz svctm  %util
> mmcblk1          0,00    2,00      0,00     36,00     0,00 0,00   0,00  
> 0,00    0,00 23189,50  46,38     0,00    18,00 500,00 100,00
>
> avg-cpu:  %user   %nice %system %iowait  %steal   %idle
>            0,25    0,00    0,00   49,62    0,00   50,13
>
> Device            r/s     w/s     rkB/s     wkB/s   rrqm/s wrqm/s  %rrqm 
> %wrqm r_await w_await aqu-sz rareq-sz wareq-sz svctm  %util
> mmcblk1          0,00    2,00      0,00     76,00     0,00 0,00   0,00  
> 0,00    0,00 46208,50  92,42     0,00    38,00 500,00 100,00
>
> avg-cpu:  %user   %nice %system %iowait  %steal   %idle
>            0,25    0,00    0,00   49,62    0,00   50,13
>
> Device            r/s     w/s     rkB/s     wkB/s   rrqm/s wrqm/s  %rrqm 
> %wrqm r_await w_await aqu-sz rareq-sz wareq-sz svctm  %util
> mmcblk1          0,00    3,00      0,00     76,00     0,00 0,00   0,00  
> 0,00    0,00 48521,67 145,56     0,00    25,33 333,33 100,00
>
> avg-cpu:  %user   %nice %system %iowait  %steal   %idle
>            0,25    0,00    0,00   49,62    0,00   50,13

So this is interesting. We can see the card is 100% busy. The IO submitted
to the card is formed by small requests - 18-38 KB per request - and each
request takes 0.3-0.5s to complete. So the resulting throughput is horrible
- only tens of KB/s. Also we can see there are many IOs queued for the
device in parallel (aqu-sz columnt). This does not look like load I would
expect to be generated by download of a large file from the web.

You have mentioned in previous emails that with dd(1) you can do couple
MB/s writing to this card which is far more than these tens of KB/s. So the
file download must be doing something which really destroys the IO pattern
(and with mb_optimize_scan=0 ext4 happened to be better dealing with it and
generating better IO pattern). Can you perhaps strace the process doing the
download (or perhaps strace -f the whole rpi-update process) so that we can
see how does the load generated on the filesystem look like? Thanks!

Honza
--
Jan Kara <jack@suse.com>
SUSE Labs, CR

\
 
 \ /
  Last update: 2022-08-16 12:22    [W:0.154 / U:0.744 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site