lkml.org 
[lkml]   [2022]   [Aug]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net 2/2] net: phy: at803x: Add disable hibernation mode support
Date
From: Wei Fang <wei.fang@nxp.com>

When the cable is unplugged, the Atheros AR803x PHYs will enter
hibernation mode after about 10 seconds if the hibernation mode
is enabled and will not provide any clock to the MAC. But for
some MACs, this feature might cause unexpected issues due to the
logic of MACs.
Taking SYNP MAC (stmmac) as an example, if the cable is unplugged
and the "eth0" interface is down, the AR803x PHY will enter
hibernation mode. Then perform the "ifconfig eth0 up" operation,
the stmmac can't able to complete the software reset operation
and fail to init it's own DMA. Therefore, the "eth0" interface is
failed to ifconfig up. Why does it cause this issue? The truth is
that the software reset operation of the stmmac is designed to
depend on the input clock of PHY.
So, this patch offers an option for the user to determine whether
to disable the hibernation mode of AR803x PHYs.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
---
drivers/net/phy/at803x.c | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 59fe356942b5..3efc6df4eb97 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -115,6 +115,7 @@
#define AT803X_DEBUG_REG_HIB_CTRL 0x0b
#define AT803X_DEBUG_HIB_CTRL_SEL_RST_80U BIT(10)
#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13)
+#define AT803X_DEBUG_HIB_CTRL_PS_HIB_EN BIT(15)

#define AT803X_DEBUG_REG_3C 0x3C

@@ -192,6 +193,9 @@
#define AT803X_KEEP_PLL_ENABLED BIT(0)
#define AT803X_DISABLE_SMARTEEE BIT(1)

+/* disable hibernation mode */
+#define AT803X_DISABLE_HIBERNATION BIT(2)
+
/* ADC threshold */
#define QCA808X_PHY_DEBUG_ADC_THRESHOLD 0x2c80
#define QCA808X_ADC_THRESHOLD_MASK GENMASK(7, 0)
@@ -730,6 +734,9 @@ static int at803x_parse_dt(struct phy_device *phydev)
if (of_property_read_bool(node, "qca,disable-smarteee"))
priv->flags |= AT803X_DISABLE_SMARTEEE;

+ if (of_property_read_bool(node, "qca,disable-hibernation"))
+ priv->flags |= AT803X_DISABLE_HIBERNATION;
+
if (!of_property_read_u32(node, "qca,smarteee-tw-us-1g", &tw)) {
if (!tw || tw > 255) {
phydev_err(phydev, "invalid qca,smarteee-tw-us-1g\n");
@@ -999,6 +1006,20 @@ static int at8031_pll_config(struct phy_device *phydev)
AT803X_DEBUG_PLL_ON, 0);
}

+static int at803x_hibernation_config(struct phy_device *phydev)
+{
+ struct at803x_priv *priv = phydev->priv;
+
+ /* The default after hardware reset is hibernation mode enabled. After
+ * software reset, the value is retained.
+ */
+ if (!(priv->flags & AT803X_DISABLE_HIBERNATION))
+ return 0;
+
+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL,
+ AT803X_DEBUG_HIB_CTRL_PS_HIB_EN, 0);
+}
+
static int at803x_config_init(struct phy_device *phydev)
{
struct at803x_priv *priv = phydev->priv;
@@ -1051,6 +1072,10 @@ static int at803x_config_init(struct phy_device *phydev)
if (ret < 0)
return ret;

+ ret = at803x_hibernation_config(phydev);
+ if (ret < 0)
+ return ret;
+
/* Ar803x extended next page bit is enabled by default. Cisco
* multigig switches read this bit and attempt to negotiate 10Gbps
* rates even if the next page bit is disabled. This is incorrect
--
2.25.1
\
 
 \ /
  Last update: 2022-08-12 08:57    [W:0.093 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site