lkml.org 
[lkml]   [2022]   [Aug]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
SubjectRe: [PATCH net] net: phy: Warn about incorrect mdio_bus_phy_resume() state
From
Hi All,

On 02.08.2022 01:34, Florian Fainelli wrote:
> Calling mdio_bus_phy_resume() with neither the PHY state machine set to
> PHY_HALTED nor phydev->mac_managed_pm set to true is a good indication
> that we can produce a race condition looking like this:
>
> CPU0 CPU1
> bcmgenet_resume
> -> phy_resume
> -> phy_init_hw
> -> phy_start
> -> phy_resume
> phy_start_aneg()
> mdio_bus_phy_resume
> -> phy_resume
> -> phy_write(..., BMCR_RESET)
> -> usleep() -> phy_read()
>
> with the phy_resume() function triggering a PHY behavior that might have
> to be worked around with (see bf8bfc4336f7 ("net: phy: broadcom: Fix
> brcm_fet_config_init()") for instance) that ultimately leads to an error
> reading from the PHY.
>
> Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This patch, as probably intended, triggers a warning during system
suspend/resume cycle in the SMSC911x driver. I've observed it on ARM
Juno R1 board on the kernel compiled from next-202208010:

 ------------[ cut here ]------------
 WARNING: CPU: 1 PID: 398 at drivers/net/phy/phy_device.c:323
mdio_bus_phy_resume+0x34/0xc8
 Modules linked in: smsc911x cpufreq_powersave cpufreq_conservative
crct10dif_ce ip_tables x_tables ipv6 [last unloaded: smsc911x]
 CPU: 1 PID: 398 Comm: rtcwake Not tainted 5.19.0+ #940
 Hardware name: ARM Juno development board (r1) (DT)
 pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
 pc : mdio_bus_phy_resume+0x34/0xc8
 lr : dpm_run_callback+0x74/0x350
 ...
 Call trace:
  mdio_bus_phy_resume+0x34/0xc8
  dpm_run_callback+0x74/0x350
  device_resume+0xb8/0x258
  dpm_resume+0x120/0x4a8
  dpm_resume_end+0x14/0x28
  suspend_devices_and_enter+0x164/0xa60
  pm_suspend+0x25c/0x3a8
  state_store+0x84/0x108
  kobj_attr_store+0x14/0x28
  sysfs_kf_write+0x60/0x70
  kernfs_fop_write_iter+0x124/0x1a8
  new_sync_write+0xd0/0x190
  vfs_write+0x208/0x478
  ksys_write+0x64/0xf0
  __arm64_sys_write+0x14/0x20
  invoke_syscall+0x40/0xf8
  el0_svc_common.constprop.3+0x8c/0x120
  do_el0_svc+0x28/0xc8
  el0_svc+0x48/0xd0
  el0t_64_sync_handler+0x94/0xb8
  el0t_64_sync+0x15c/0x160
 irq event stamp: 24406
 hardirqs last  enabled at (24405): [<ffff8000090c4734>]
_raw_spin_unlock_irqrestore+0x8c/0x90
 hardirqs last disabled at (24406): [<ffff8000090b3164>] el1_dbg+0x24/0x88
 softirqs last  enabled at (24144): [<ffff800008010488>] _stext+0x488/0x5cc
 softirqs last disabled at (24139): [<ffff80000809bf98>]
irq_exit_rcu+0x168/0x1a8
 ---[ end trace 0000000000000000 ]---

I hope the above information will help fixing the driver.

> ---
> drivers/net/phy/phy_device.c | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
> index 46acddd865a7..608de5a94165 100644
> --- a/drivers/net/phy/phy_device.c
> +++ b/drivers/net/phy/phy_device.c
> @@ -316,6 +316,12 @@ static __maybe_unused int mdio_bus_phy_resume(struct device *dev)
>
> phydev->suspended_by_mdio_bus = 0;
>
> + /* If we managed to get here with the PHY state machine in a state other
> + * than PHY_HALTED this is an indication that something went wrong and
> + * we should most likely be using MAC managed PM and we are not.
> + */
> + WARN_ON(phydev->state != PHY_HALTED && !phydev->mac_managed_pm);
> +
> ret = phy_init_hw(phydev);
> if (ret < 0)
> return ret;

Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland

\
 
 \ /
  Last update: 2022-08-12 13:20    [W:1.890 / U:0.168 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site