lkml.org 
[lkml]   [2022]   [Jul]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v1 1/4] PCI: brcmstb: Split brcm_pcie_setup() into two funcs
On Fri, Jul 8, 2022 at 3:04 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
>
> On Fri, Jul 08, 2022 at 09:29:27AM -0400, Jim Quinlan wrote:
> > On Wed, Jul 6, 2022 at 5:56 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
> > > On Fri, Jul 01, 2022 at 12:27:22PM -0400, Jim Quinlan wrote:
> > > > We need to take some code in brcm_pcie_setup() and put it in a new function
> > > > brcm_pcie_linkup(). In future commits the brcm_pcie_linkup() function will
> > > > be called indirectly by pci_host_probe() as opposed to the host driver
> > > > invoking it directly.
> > > >
> > > > Some code that was executed after the PCIe linkup is now placed so that it
> > > > executes prior to linkup, since this code has to run prior to the
> > > > invocation of pci_host_probe().
> > >
> > > This says we need to move some code from brcm_pcie_setup() to
> > > brcm_pcie_linkup(), but not *why* we need to do that.
> > I will elaborate in the commit message.
> > >
> > > In brcm_pcie_resume(), they're called together:
> > >
> > > brcm_pcie_resume
> > > brcm_pcie_setup
> > > brcm_pcie_linkup
> > >
> > > In the probe path, they're not called together, but they're in the
> > > same order:
> > >
> > > brcm_pcie_probe
> > > brcm_pcie_setup
> > > pci_host_probe
> > > ...
> > > brcm_pcie_add_bus # bus->ops->add_bus
> > > brcm_pcie_linkup
> > >
> > > Is there something that must happen *between* them in the probe path?
> >
> > Yes. In the probe() case, we must do things in this order:
> >
> > 1. brcm_pcie_setup()
> > 2. Turn on regulators
> > 3. brcm_pcie_linkup()
>
> Ah, I see, both 2) and 3) happen in brcm_pcie_add_bus:
>
> brcm_pcie_add_bus # bus->ops->add_bus
> pci_subdev_regulators_add_bus
> regulator_bulk_enable # turn on regulators
> brcm_pcie_linkup
>
> > Since the voltage regulators are turned on during enumeration,
> > pci_host_probe() must be invoked prior to 3. Before regulators, we
> > did not care.
>
> I guess in the pre-regulator case, i.e., pcie->sr not set, the power
> for downstream devices must always be on.
>
> > In the resume case, there is no enumeration of course but our driver
> > has a handle to the regulators and can turn them on/off w/o help.
>
> And I guess we don't need brcm_pcie_setup() in the resume path because
> suspend turns off power only for downstream devices, not for the root
> port itself, so the programming done by brcm_pcie_setup() doesn't need
> to be done again.

I'm not sure I understand what you are saying -- brcm_pcie_setup() is
called by brcm_pcie_resume()
because it is needed. brcm_pcie_setup() isn't concerned with power it
just does the preparation
required before attempting link-up.

Regards,
Jim Quinlan
Broadcom STB


>
> > > > Link: https://lore.kernel.org/r/20220106160332.2143-5-jim2101024@gmail.com
> > > > Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
> > > > ---
> > > > drivers/pci/controller/pcie-brcmstb.c | 69 +++++++++++++++++----------
> > > > 1 file changed, 43 insertions(+), 26 deletions(-)
> > > >
> > > > diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
> > > > index e61058e13818..2bf5cc399fd0 100644
> > > > --- a/drivers/pci/controller/pcie-brcmstb.c
> > > > +++ b/drivers/pci/controller/pcie-brcmstb.c
> > > > @@ -926,16 +926,9 @@ static inline int brcm_pcie_get_rc_bar2_size_and_offset(struct brcm_pcie *pcie,
> > > >
> > > > static int brcm_pcie_setup(struct brcm_pcie *pcie)
> > > > {
> > > > - struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
> > > > u64 rc_bar2_offset, rc_bar2_size;
> > > > void __iomem *base = pcie->base;
> > > > - struct device *dev = pcie->dev;
> > > > - struct resource_entry *entry;
> > > > - bool ssc_good = false;
> > > > - struct resource *res;
> > > > - int num_out_wins = 0;
> > > > - u16 nlw, cls, lnksta;
> > > > - int i, ret, memc;
> > > > + int ret, memc;
> > > > u32 tmp, burst, aspm_support;
> > > >
> > > > /* Reset the bridge */
> > > > @@ -1025,6 +1018,40 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
> > > > if (pcie->gen)
> > > > brcm_pcie_set_gen(pcie, pcie->gen);
> > > >
> > > > + /* Don't advertise L0s capability if 'aspm-no-l0s' */
> > > > + aspm_support = PCIE_LINK_STATE_L1;
> > > > + if (!of_property_read_bool(pcie->np, "aspm-no-l0s"))
> > > > + aspm_support |= PCIE_LINK_STATE_L0S;
> > > > + tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
> > > > + u32p_replace_bits(&tmp, aspm_support,
> > > > + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK);
> > > > + writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
> > > > +
> > > > + /*
> > > > + * For config space accesses on the RC, show the right class for
> > > > + * a PCIe-PCIe bridge (the default setting is to be EP mode).
> > > > + */
> > > > + tmp = readl(base + PCIE_RC_CFG_PRIV1_ID_VAL3);
> > > > + u32p_replace_bits(&tmp, 0x060400,
> > > > + PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK);
> > > > + writel(tmp, base + PCIE_RC_CFG_PRIV1_ID_VAL3);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int brcm_pcie_linkup(struct brcm_pcie *pcie)
> > > > +{
> > > > + struct pci_host_bridge *bridge = pci_host_bridge_from_priv(pcie);
> > > > + struct device *dev = pcie->dev;
> > > > + void __iomem *base = pcie->base;
> > > > + struct resource_entry *entry;
> > > > + struct resource *res;
> > > > + int num_out_wins = 0;
> > > > + u16 nlw, cls, lnksta;
> > > > + bool ssc_good = false;
> > > > + u32 tmp;
> > > > + int ret, i;
> > > > +
> > > > /* Unassert the fundamental reset */
> > > > pcie->perst_set(pcie, 0);
> > > >
> > > > @@ -1075,24 +1102,6 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
> > > > num_out_wins++;
> > > > }
> > > >
> > > > - /* Don't advertise L0s capability if 'aspm-no-l0s' */
> > > > - aspm_support = PCIE_LINK_STATE_L1;
> > > > - if (!of_property_read_bool(pcie->np, "aspm-no-l0s"))
> > > > - aspm_support |= PCIE_LINK_STATE_L0S;
> > > > - tmp = readl(base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
> > > > - u32p_replace_bits(&tmp, aspm_support,
> > > > - PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK);
> > > > - writel(tmp, base + PCIE_RC_CFG_PRIV1_LINK_CAPABILITY);
> > > > -
> > > > - /*
> > > > - * For config space accesses on the RC, show the right class for
> > > > - * a PCIe-PCIe bridge (the default setting is to be EP mode).
> > > > - */
> > > > - tmp = readl(base + PCIE_RC_CFG_PRIV1_ID_VAL3);
> > > > - u32p_replace_bits(&tmp, 0x060400,
> > > > - PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK);
> > > > - writel(tmp, base + PCIE_RC_CFG_PRIV1_ID_VAL3);
> > > > -
> > > > if (pcie->ssc) {
> > > > ret = brcm_pcie_set_ssc(pcie);
> > > > if (ret == 0)
> > > > @@ -1281,6 +1290,10 @@ static int brcm_pcie_resume(struct device *dev)
> > > > if (ret)
> > > > goto err_reset;
> > > >
> > > > + ret = brcm_pcie_linkup(pcie);
> > > > + if (ret)
> > > > + goto err_reset;
> > > > +
> > > > if (pcie->msi)
> > > > brcm_msi_set_regs(pcie->msi);
> > > >
> > > > @@ -1398,6 +1411,10 @@ static int brcm_pcie_probe(struct platform_device *pdev)
> > > > if (ret)
> > > > goto fail;
> > > >
> > > > + ret = brcm_pcie_linkup(pcie);
> > > > + if (ret)
> > > > + goto fail;
> > > > +
> > > > pcie->hw_rev = readl(pcie->base + PCIE_MISC_REVISION);
> > > > if (pcie->type == BCM4908 && pcie->hw_rev >= BRCM_PCIE_HW_REV_3_20) {
> > > > dev_err(pcie->dev, "hardware revision with unsupported PERST# setup\n");
> > > > --
> > > > 2.17.1
> > > >
> > > >
> > > > _______________________________________________
> > > > linux-arm-kernel mailing list
> > > > linux-arm-kernel@lists.infradead.org
> > > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
>
>
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
[unhandled content-type:application/pkcs7-signature]
\
 
 \ /
  Last update: 2022-07-08 21:43    [W:0.088 / U:0.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site